Club Car Pioneer 1200 Скачать руководство пользователя страница 118

Страница: 118 / 360

PERIODIC MAINTENANCE

Battery

Page 10-8 2001 Pioneer 1200 Gasoline Vehicle Maintenance and Service Manual

Fueling Instructions, Continued:

2. Remove fuel cap and fill the fuel tank with fresh, unleaded gasoline only (Figure 10-5, Page 10-7). See

following CAUTION and NOTE.

∆ CAUTION

• To allow for expansion, do not fill higher than one inch (2.54 cm) from the top of the fuel tank. Avoid

spilling fuel.

NOTE: Whenever possible, avoid using oxygenated fuels and fuels that are blended with alcohol. Vehicles to

be stored for extended periods should be prepared for storage as instructed in Section 3 of this man-
ual. See Storage – Gasoline Vehicle, Section 3, Page 3-1.

3. Replace fuel cap on tank. Make sure cap is tightened securely.

4. Replace passenger seat. See following WARNING.

∆ WARNING

• Make sure seat hinges and latch are securely engaged before operating vehicle.

BATTERY

For periodic battery maintenance, see Battery, Section 12, Page 12-31.

Содержание Pioneer 1200









































































































































































































































































































































































Результаты поиска

Содержание Pioneer 1200

Отзывы:

Похожие инструкции для Pioneer 1200

Бренды по названию

Популярные бренды

Club Car Pioneer 1200, Руководство по техническому обслуживанию

Результаты поиска

Содержание Pioneer 1200

Отзывы:

Похожие инструкции для Pioneer 1200

Бренды по названию

Популярные бренды