29
Program Menu
IQ DISPLAY MODULE (IQDM-P) SERIES
2 PROGRAMMING
PROGRAM MENU
The
program
menu can be accessed by pressing the right arrow on the navigation button when the square beside
program
is blinking
. When the
program
menu is active, use the up or down arrows on the
navigation button to go to the desired item in the
program
menu. Again, press the right arrow to select the menu item.
Use the change value button to change the values of the selected item by pr or -.
The following parameters can be programmed with the handset from the
program
menu:
NOTE:
M1 refers to “Mode 1” and M2 refers to “Mode 2.” To activate Mode 2 in the IQDM-P Series 2, Code A, Code B
and Code C must be entered.
See Code A, Code B, and Code C on page 29-4.
All settings in Mode 2 are
programmed with the same procedues as Mode 1.
M1/M2 SPEED
The vehicle’s top speed can be changed by selecting values 1 through 4.
See chart below.
SPEED SETTING
VEHICLE SPEED
1
8.0 mph (12.9 km/h)
2
12 mph (19.3 km/h)
3
15 mph (24.1 km/h)
4
17 mph (27.4 km/h)
A vehicle programmed for speed setting 4 does not conform to ANSI Z130.1 – American National Standard for Golf
Cars – Safety and Performance Specifications because it is capable of speeds in excess of 15 mph (24.1 km/h). For
more information on this feature, contact your local Club Car distributor or dealer.
M1/M2 FAST ACCEL
M1/M2 fast accel
(fast acceleration) is an option that can be enabled or disabled. With
fast accel
turned on, the vehicle
will accelerate at a noticeably faster rate. With this feature turned off, the vehicle speed will gradually increase, even if
the accelerator is quickly pressed to the floor. Turn the feature on or off by pr or – on the change value button.
M1/M2 PEDAL UP
Three options exist for
M1/M2 pedal up
(motor braking). On a level surface, when the accelerator pedal is released,
motor braking will slow the vehicle to a stop when pedal up motor braking is enabled (option 1 or 2). If pedal up motor
braking is disabled (option 0), the vehicle will coast to a stop when the pedal is released.
When the vehicle is going down an incline, and the accelerator pedal is released motor braking will slow the vehicle to
a controlled speed directly proportional to the slope of the incline when pedal up motor braking is enabled (option
1 or 2). If pedal up motor braking is disabled (option 0), the vehicle will coast up to the programmed top speed
when the pedal is released.
Change the settings of the M1/M2 Pedal Up by pr or – on the change value button.
M1/M2 PEDAL UP SETTING
MODE
OPERATION DESCRIPTION
0
Off
Pedal up motor braking is disabled
1
Mild pedal up
Mild pedal up motor braking
2
Aggressive pedal up
Aggressive pedal up motor braking
Page 29-2
2007-2009 Turf 252, Carryall 252 and XRT 900 Maintenance and Service Manual
Содержание CARRYALL 252 2007
