Cloudray MYJG-50 Скачать руководство пользователя страница 2

Power Supply MYJG-50 User Manual

www.cloudraylaser.com

2

Withstand Voltage

Input-Output, Input-Enclosure: AC1500V 10mA 60S; Output cathode is

connected with enclosure.

Weight

1.6kg

Environment

Working Temperature

(-10~40

), Relative Humidity (RH)≤90%

Cooling Way

Force-Air Cooling (FAC)

III. Operation Instruction

1. Laser Tube Connection:

(Referring to Power Supply and Laser Device's Connection

Diagram)
High voltage terminal (HV+) of MYJG-50 power supply should be connected to the

positive pole of CO2 laser device. Current circuit of the power supply shall be connected
to negative pole (laser output terminal) of laser device, through an ampere meter or
directly.

2. Connection of Control Signal

The control signal shall be reliably connected to control terminal of the power supply

MYJG-50, after connecting the DAC output signal and TTL signal of external computer
with the power supply, the laser device shall work as expected. If the laser lamp can not
work properly, should check the control signal is correct or not(include check the voltage
specification and logic), if use PWM control as power control, make sure f≥20KHz,
amplitude (peak value) ≤5V, Check and make sure protection switch WP connection is
correct at same time.

3. Voltage of Power Input:

MYJG-50W's power input of the power supply shall be 220VAC/50Hz. This power

supply can be adjusted for 110V or 220V.

4. Others:

A group of protection switches are also reserved for detection of water switch, fan

switch, open-enclosure protection and so on.

Caution:

1) Water cooling system should be working properly when switching on laser device.
2) Circuit of high voltage output should not be open! [High voltage output terminals

(positive and negative poles) shall be properly connected to positive and negative
poles of laser device, respectively.]

3) Attentions should be given to avoid any electric shock after the power supply being

switched off. (The

Insulation Safety Requirements

should be 40KV between the

terminal of output and "G")

4) Well-grounded three-pole receptacle should be used to the supply power. The

enclosure should be well grounded to avoid electric shock.

www.cloudraylaser.com

www.cloudraylaser.com

www.cloudraylaser.com

www.cloudraylaser.com

www.cloudraylaser.com

www.cloudraylaser.com

www.cloudraylaser.com

www.cloudraylaser.com

www.cloudraylaser.com

Содержание MYJG-50








Отзывы: