background image

M09G60E14-04 

MSAT-XEE 8.2-30.2  

9

4  Refrigeranting connections

The sizing of the refrigerating connection lines is of extreme importance for the system operating and reliability.

The diameter of the connection between the two units is function of distances, differences in level and curve number; it has so to be calculated 

by a qualified technician.

Incorrect sizing may damage the compressor or affect cooling capacity.
The operations must be performed by an expert refrigerator technician
use only a copper pipe for chiller operating
pipes must not to be too much long and with too much curves
for a good efficiency do not perform curves with a radium too much short and avoid the pipe crushing
to allow the vacuum and charge operations install service fittings on pipes (if the unit is not fitted with taps with service fittings)
pipes must be perfectly clean (perform a cleaning with nitrogen or dry air before connecting the pipes to the two units) and without humidity 

to allow a good vacuum operation

The installation of the pipes may affect the level of noise in the system:

 install flexible joints between the unit and the pipes

 the pipe weight has not to weigh on units but it has to be sustained by anchorage brackets

 Brackets must allow the pipe thermal expansion

 Install antivibration material between the brackets and the pipes so as to prevent the transmission of vibrations

4.1  Shut-off valves

A.  Shut-off  valves

4.2  Risk of explosion

When you install cut-off devices (solenoid valves, taps, etc.), be aware that they may cause traps for refrigerant in the form of closed zones 

upstream and downstream where the refrigerant cannot freely expand.

In this situation, if there is an increase in temperature (due to exposure to the sun, proximity of pipes or sources of heat), the expansion of the 

trapped gas may cause the refrigeration pipes to explode.

Evaluate whether safety valves can be installed, especially in the liquid pipes that are most exposed to this risk.

Содержание MSAT-XEE 10.2











































Отзывы: