Clinton MINI-TAURUS 990 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 19

Clinton MINI-TAURUS 990 Скачать руководство пользователя страница 7

3. **** TOGGLE SWITCHES

a. DIRECTION
Sets the direction of the motor either clockwise (++cw) or counterclockwise (--ccw).
Default: --ccw

b. AUTOMODE ( Automatic mode)
If set to "AUTO" when material is placed in the machine covering the photo eye and
the treadle is pressed the machine will sew at maximum speed until the photo eye is
uncovered.
Default: man (manual)

c. CYC. STRT (Cycle start)
If selected this parameter will only let the cycle start if the photo eye is covered.
Default: Eye Cov. (Eye Covered)

d. TREADLE
If this parameter is set to;
continue: The new cycle will start depending on the condition of the photo eye
(covered or uncovered) and the setting of the "CYC. STRT" parameter.
ped.neut. (pedal neutral). The new cycle will start only after the pedal has been
returned to the neutral position.
Default: ped. neut

e. SFTY SW (Safety Switch)
This parameter enables or disables the safety switch if one is used.
Default: Off

f. SFTY SW SEW
This parameter sets, whether the safety switch is normally opened or normally
closed, in order for the machine to start.
Default: cls (closed)

2-4

ML990-7A

«
...
5
6
7
8
9
...
»

Содержание MINI-TAURUS 990




















Отзывы:

Нет отзывов