3
⚫
⚫
B
B
a
a
t
t
t
t
e
e
r
r
y
y
⚫
The PIR Camera uses four AAL91 lithium batteries as its power source.
⚫
The PIR Camera features low battery voltage detection. When low battery is detected, a low battery signal will be sent
to the Control Panel along with regular signal transmissions for the Control Panel to display the status accordingly.
⚫
To Change Battery:
Step 1:
Navigate the Control Panel into Programming mode.
Step 2:
Remove the PIR Camera from mounting position and loosen the back cover fixing screw.
Step 3:
Insert a flat-head screwdriver to the caved-in area of the back cover and then carefully lift the back cover.
Step 4:
Remove the old batteries and press the
test button twice to fully discharge.
Step 5:
Insert four new AAL91 lithium batteries.
Step 6:
Press the test button once. A battery
normal signal will be sent to the Control Panel.
Step 7:
Screw back the back cover.
Step 8:
Mount back the PIR Camera to
mounting location.
Step10:
Navigate the Control Panel to exit Programming mode and return to operation mode. The procedure is complete.
⚫
⚫
G
G
e
e
t
t
t
t
i
i
n
n
g
g
S
S
t
t
a
a
r
r
t
t
e
e
d
d
–
–
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
t
t
h
h
e
e
P
P
I
I
R
R
C
C
a
a
m
m
e
e
r
r
a
a
i
i
n
n
t
t
o
o
t
t
h
h
e
e
C
C
o
o
n
n
t
t
r
r
o
o
l
l
P
P
a
a
n
n
e
e
l
l
⚫
Loosen the bottom fixing screw, and then insert a flat-head screwdriver to lift the back cover.
⚫
Based on your needs, set Sensitivity Switch as shown in
DIP Switch Position Table
.
⚫
Insert four AAL91 lithium batteries into the battery holder taking care to connect the polarity correctly.
⚫
Put the Control Panel into learning mode, refer to Control Panel manual for details.
⚫
Press and hold the Test button for 3 seconds to send a learn code, and then release the button when Red LED lights
up. The LED will be on for 20 seconds, indicating that the PIR Camera is in learning mode.
⚫
If the Control Panel receives the signal from the PIR Camera, it will display the information accordingly. Within 20
seconds when the LED of the PIR Camera is on, select the PIR Camera on the Control Panel Webpage and click
“add”
to include it into the Panel. Refer to the Control Panel manual for details.
⚫
When the PIR Camera receives acknowledgement from the Control Panel, the LED of the PIR Camera will flash 6
times and then turn off to indicate successful learning.
⚫
After the PIR Camera is learnt-in, put the Control Panel into Walk Test mode. Hold the PIR Camera in the desired
location, and press the Test button to confirm this location is within the signal range of the Control Panel.
⚫
When you are satisfied that the PIR Camera works in the chosen location, you can proceed to installation.
<
<
N
N
O
O
T
T
E
E
>
>
After the Test button is held and pressed for 3 seconds, the LED of the PIR Camera will be on for 20 seconds. If
the PIR Camera does not receive acknowledgement from the Control Panel within this 20-second period, the LED
will turn off. The Test button needs to be pressed and held for 3 seconds again to resend a learning code.
If the PIR Camera already exists in a Control Panel system, you will need to first remove the PIR Camera from the
Control Panel before you can learn it into a different Control Panel.
Walk Test
should be conducted to confirm proper operation and coverage of the PIR.
When learning the PIR Camera into a repeater/router, please press the Test button once (instead of pressing and
holding it for 3 seconds) to send a learn code.
⚫
⚫
E
E
d
d
i
i
t
t
P
P
I
I
R
R
C
C
a
a
m
m
e
e
r
r
a
a
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
A
A
r
r
e
e
a
a
Follow instruction below to change PIR Camera Area in the
Control Panel
1) Use the panel Edit Device function to change PIR Camera
area setting.
2) Press and hold the Test button for 3 seconds on the PIR
Camera to send a signal to the panel, and then release the
button when the LED lights up.
⚫
⚫
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
&
&
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
M
M
e
e
t
t
h
h
o
o
d
d
◆
Mounting with mounting bracket:
⚫
The PIR Camera can be mounted on either a flat surface or
in a corner situation with fixing screws, plugs, and the
mounting bracket provided.
⚫
The provided mounting plate has knockouts, where the
plastic is thinner and can be broken for mounting purpose.
Two knockouts are for surface fixing and four knockouts are