3
z
z
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
P
P
r
r
o
o
c
c
e
e
d
d
u
u
r
r
e
e
s
s
:
:
Step 1. Put Keypad in Test mode by entering “
0000
” (default PIN code), then press
＊
. Keypad will sound 1
long beep and the Green Active LED will steadily flash.
Step 2. Adding Keypad into the Control Panel:
I. Put the Control panel into
/-
menu and select the
Add Devices
sub menu.
II. Press
＊
and then
1
when requested. Keypad and Control Panel will beep once.
III. Refer to the operation manual of your control Panel under the section of
/-
to complete
the learn-in process.
Step 3. After the Keypad is learnt-in, put the Control Panel into
Walk Test
mode, hold the Keypad in the
desired location, press the
＊
then
1
button to confirm this location is within signal range of the
Control Panel.
Step 4. When you are satisfied that the Keypad works in the chosen location, you can proceed with mounting
the Keypad following the steps described below (see
Mounting Keypad)
.
Step 5. Setting the Pin Code:
I. Press
＊
then
6
, a long beep will be sound.
II. Enter
0000
(default PIN code)
III. Press
Χ
, Keypad sounds a long beep.
IV. Enter your new 4-digit code.
V. Press
#
, Keypad sounds a long beep.
Step 6. Press
twice
to exit Test mode and the installation is completed.
z
z
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
t
t
h
h
e
e
K
K
e
e
y
y
p
p
a
a
d
d
:
:
To mount the Keypad:
I. Remove the 2 slide-out sections of front cover.
II. Using the 2 mounting holes as a template, mark off the positions in the most appropriate place.
III. Insert the wall plugs if fixing into plaster or brick surface.
IV. Screw the Keypad onto the wall plugs.
V. Replace the 2 slide-out sections.
z
z
H
H
o
o
w
w
t
t
o
o
S
S
e
e
t
t
S
S
y
y
s
s
t
t
e
e
m
m
M
M
o
o
d
d
e
e
:
:
Arm/Home with Pin Code
¾
Arm Mode
: Enter anyone of Control Panel user codes and press
key. Red TX LED will flash 5
times and the Keypad sounds a long beep.
¾
Home Mode
: Enter anyone of Control Panel user codes and press
key. Red TX LED will flash 5
times and the Keypad sounds 3 beeps.
¾
Disarm Mode
: Enter anyone of Control Panel user codes and press
key. Red TX LED will flash 5
times and the Keypad sounds 2 beeps.
¾
Enter Test Mode — Enter Keypad PIN code and press
＊
key. The Keypad will sound 1 long beep and
Green Active LED flashes steadily.
¾
Panic Alarm — Press
1
+
3
simultaneously at the same time. Red TX LED will flash 5 times and the
Keypad sounds a long beep.
¾
Fire Alarm — Press
4
+
6
simultaneously at the same time. Red TX LED will flash 5 times and the
Keypad sounds a long beep.
¾
Medical Alarm — Press
7
+
9
simultaneously at the same time. Red TX LED will flash 5 times and the
Keypad sounds a long beep.
¾
For wrong entering or operating the Keypad will sound 4 short beeps.
Arm/ Home without PIN Code
¾
Arm Mode
: Press
key. Red TX LED will flash 5 times and the Keypad sounds a long beep.
¾
Home Mode
: Press
key.
Red TX LED will flash 5 times and the Keypad sounds 3 beeps.
¾
Disarm Mode
: Enter anyone of Control Panel user codes and
Key. Red TX LED will flash 5 times
and the Keypad sounds 2 beeps.
