3
Step 2. Find the location where the Bellbox is to be mounted.
Step 3. Remove the Top cover by releasing the bottom screw using a Philips screwdriver
and pulling the outer case out carefully.
Step 4. Remove the LED cover by releasing the 2 screws securing the cover using a
Philips screwdriver and removing the cover.
Step 5. Hold the Bellbox at the position where it will be mounted, supply power to Bellbox.
Step 6. Check whether BX has a strong enough signal with the Control Panel by putting
the Control Panel into
Walk Test
mode (please refer to Control Panel manual).
Press the
Learn Button
check whether the signal is strong enough (please refer
to Control Panel manual for signal strength).
Step 7. If you are satisfied with the signal strength, remove the Bellbox from mounting
location. Replace the LED cover and secure it with the 4 LED cover screws using
a Philips screwdriver.
Step 8. Identify the 4 mounting holes, mount and fix the Bellbox on the wall using the
large screws and wall plugs provided. Secure the screws using a Philips
screwdriver. Make sure the Tamper Switch is fully depressed against the wall.
<NOTE>
The tamper switch protrudes through the back of the unit. When the siren is
pulled off from the wall, the alarm will be activated. Ensure it is fully depressed
when the siren is mounted. If there is a gap, pack with a suitable spacing
material.
Step 9. Replace the Top cover by hooking the top of the Top cover onto the top of the
base. Push the bottom of the Top cover onto the base and tighten the bottom
screw using a Philips screwdriver.
Step 10. Enable Siren Tamper function on the Control Panel (Please refer to the Control
Panel instruction manual)
Step 11. Check if the installation is successful by testing from the Control Panel by arming
and disarming function.
Successful arming/disarming is indicated by the table provided in
Audio & Visual
Status Indication
.
<NOTE>
If 5 short-beeps are noticed while arming/disarming, it means the tamper is not
fully depressed. Check to ensure that tamper is properly set and then test from
Control Panel again.
Step 12. The installation is now completed.
Changing the Battery
Step 1: Disable the Siren Tamper function on the Control Panel (please refer to the Control Panel instruction manual). BX-23 will sound a beep to
indicate the tamper switch is now disabled.
Step 2: Release the cover-fixing screw at the bottom of BX-23 using a Philips screwdriver and pull the outer case out carefully.
Step 3: Remove the LED cover by releasing the 4 screws securing the cover using a Philips screwdriver and removing the cover.
Step 4: Slide Power switch to the off position.
Step 5: The battery compartment is a large box in the BX-23 with a lid secured with 4 screws. Release the four screws using a Philips
screwdriver and take off the compartment lid.
Step 6: Remove the old batteries and press the Tamper Switch twice to discharge.
Step 7: Insert new batteries into the battery compartment.
Step 8: After inserting all batteries, slide the power switch to the BT4 terminal. All the LED will flash once and the buzzer will emit 1 beep as the
bellbox powers on.
Step 9: Replace the LED cover and secure it with the 4 screws securing the cover using a Philips screwdriver.
Step 10: Replace the battery compartment lid and secure it with the four screws using a Philips screwdriver. Please do not over tighten.
Step 11: Replace the Top cover by hooking the top of the Top cover onto the top of the base. Push the bottom of the Top cover onto the base and
tighten the bottom screw using a Philips screwdriver.
Step 12: Enter the Control Panel Program Siren webpage again to enable the Siren Tamper function again. The BX-23 will sound a beep to
indicate the tamper switch is now activated.
Factory Reset
The Bellbox can be reset and memory contents cleared. Whenever the Bellbox is removed from the Control Panel, it should be put to factory reset
to clear its Control Panel memory, otherwise the Bellbox will still raise alarm if it receives alarm signal from panel.
Step 1: Disable the Siren Tamper function on the Control Panel (please refer to the Control Panel instruction manual). The Bellbox will sound a
beep to indicate the tamper switch is now disabled.
Step 2: Remove the Bellbox from Control Panel device list (please refer to the Control Panel instruction manual).
Step 3: Release the bottom screw of the Top cover using a Philips screwdriver, remove the top cover..