ClimateMaster Trilogy Q-Mode (QE) Series Скачать руководство пользователя страница 73

Страница: 73 / 92

c l i m a t e m a s t e r.c o m

Trilogy

Q-Mode

(QE) Series IOM - 60Hz HFC-410A

R e v i s e d : D e c e m b e r 2 2 , 2 0 2 1

Table 16: Troubleshooting (Cont.)

Code

Fault

Mode

Possible Cause

Solution

Low Suction Superheat

ALL

Faulty EEV

Check EEV operation

ALL

Bad suction pressure trans-

ducer

Troubleshoot transducer

ALL

Bad suction temp sensor

Check temp vs. resistance curve per calculator

ALL

Improperly installed suction

temp sensor

Check location and position of temp sensor

High Suction Superheat

ALL

Faulty EEV

Check EEV operation

ALL

Bad check valve

Check temp across check valve in unused circuit to determine if there

is leakage

ALL

Low charge

Check unit capacity in mode check

ALL

Bad suction pressure

transducer

Troubleshoot transducer.

ALL

Bad suction temp sensor

Check temp vs. resistance curve per calculator.

ALL

Improperly installed suction

temp sensor

Check location and position of temp sensor.

General Compressor Fault

Mitsubishi Inverter 0930

HT, CL

Check compressor sub faults

See Low Level sub-faults (codes 61-71, 75 and 76).

Carel Inverter 1860

HT, CL

Data reception failure

Check the serial connection. Switch the drive off and back on again. In

case of persistance, call for assistance.

HT, CL

Execution of reset parameter

default command;

Parameters user setting

corrupted

Set parameters.

HT, CL

Wrong parameters values or

unsuited load

Switch the drive off and back on again. Check the parameters values.

Check the motor load.

HT, CL

Refer to class A alarm 13

refer to class A alarm 13

High temp Shutdown

Mitsubishi Inverter 0930

HT, CL

Improper contact with heat sink Check heat sink contact with inverter board.

HT, CL

Damaged thermistor

Replace inverter board if reading coming back from board is higher

than 200ºF

***WARNING - Inverter board capacitors maintain high voltage for up

to 15 minutes before fully discharging.

Carel Inverter 1860

HT, CL

The temperature inside the

drive has exceeded the

maximum level allowed.

Check that the quantity and flow of cooling air ar regular. Check that

there is not dust in the heat sink. Check the environment temperature.

Ensure that the switching frequency is not too high with respect to the

environment temperature and the motor load.

HT, CL

The temperature of the drive is

lower than the minimum level

allowed.

Warm up the ambient where the drive is installed.

HT, CL

•

Blockage in the cooling

system

•

Minimum distance for inverter

positioning not respected

(see manual)

•

Cooling system not working

properly

Check quality (dirt) and quantity of cooling air.

Check ambient temperature.

HT, CL

•

Cooling system not working

properly

•

Unsuitable environment

Check ambient temperature.

HT, CL

PFC overcurrent

Reset alarm. In case of persistance, call for assistance.

Содержание Trilogy Q-Mode (QE) Series





























































































Результаты поиска

Содержание Trilogy Q-Mode (QE) Series

Отзывы:

Бренды по названию

Популярные бренды

ClimateMaster Trilogy Q-Mode (QE) Series, Руководство пользователя

Результаты поиска

Содержание Trilogy Q-Mode (QE) Series

Отзывы:

Бренды по названию

Популярные бренды