background image

Tranquility

®

 Digital Air Handler (TAH) 

R e v. : A u g u s t   2 1 ,   2 0 1 8

18

G e o t h e r m a l   H e a t i n g   a n d   C o o l i n g

1.   TAH Air Handlers are shipped from the factory wired 

for 230 volts. The units may be wired for 208 or 115 

volts. Follow instructions on unit wiring diagram located 

on blower housing and in the Service Facts document 

included with the unit.

2.   The selection of wire and fuse sizes should be made 

according to the Minimum Branch Circuit Ampacity and the 

Maximum Overcurrent Device listed on the unit nameplate.

3.   Field wiring diagrams for electric heaters and unit 

accessories are shipped with the accessory.

4.   Wiring must conform to National and Local codes.

5.   Ground unit per local codes with good safety procedures.

NOTE: If air handler is used with or without a 

heater, the electrical entry hole as well as any other 

cabinet penetrations must be sealed air-tight.

Wiring Instructions for 115v Conversion from 230 volt

1.  Disconnect all power to the unit.

2.  Disconnect Transformer primary orange wire from power 

block T2 and insulate open end of wire. Connect the 

white lead from transformer primary wire to power block 

terminal T2. Note: (L2 will be used as Netural) 

3.  Remove plug in ECM power wiring harness (Fig. 13) and 

Install 2 pin jumper plug provided in control box (Fig. 14).

NOTE: When supplementary heaters are installed, 

inspect to insure that all packaging material has 

been removed.

Electrical - Power Wiring

� 

WARNING! 

Figure 13: Remove Harness Plug

Note: For 115v power only. Damage will occur to motor 

with 230v power supply if 115v jumper is used.

Table 4: Electric Table (115) 208/230

WARNING!  

Electrical shock hazard - Lock unit disconnect 

switch in open position before servicing unit. Failure 

to follow this warning could result in property damage, 

personal injury, or death.

Figure 14: Install Two Pin Jumper Plug

Model

Fan  

Motor FLA

Fan 

Motor 

HP

Max

Fan

ESP

Min Circ 

Amp

(120) 

208/230

Total 

Unit 

FLA

Max Fuse/ 

HACR

(120) 

208/230

026

(7.7) 4.3

1/2

0.5

(7.8) 4.9

(7.7) 4.3

(15) 15

038

(7.7) 4.3

1/2

0.5

(7.8) 4.9

(7.7) 4.3

(15) 15

049

(12.8) 7

1

1

(14.4) 8.6

(12.8) 7

(25) 15

064

(12.8) 7

1

1

(14.4) 8.6

(12.8) 7

(25) 15

Dual Rated Voltate: (115) 208/230

Min/Max Voltage: 115: 114/132

Min/Max Voltage: 208/230: 197/252

Содержание TAH 026-A

























Отзывы: