ClimaCool FLEX 30 Скачать руководство пользователя | Manualshive

Страница: 39 / 50

background image

^^^JSPTHJVVSJVYWJVT

®

37

Sequence of Operation

SEQUENCE OF OPERATION
GENERIC INTERFACE - MANUAL ISOLATION
VALVES

Sequence of Operations

Chiller shall be enabled locally or remotely from enable/
disable contact by BAS via selector switch on face of the
"Master Control Panel". Pumps for chilled water supply and
condenser water supply shall be started by others. When
proof of ﬂow is established in both the chilled water and
condenser water lines, the ClimaCool chiller shall start. The
"Chilled Water Supply" (CHWS) temp. sensor (TS1), located
in the discharge line of respective chiller shall be used to
cycle compressor stages sequentially to maintain set point of
45°F (adjustable from the LCD Display on the Face of the
"Master Control Panel", or Remotely via 4-20 ma signal.)

Chillers will be disabled until "Chilled Water Return"
(CHWR) temperature sensor is below 90°F and "Condenser
Water Supply" (CWS) temperature sensor is above 65°F.

Each module of the chiller has 2 compressors. Stage 1
compressors shall be started ﬁrst on lead week and stage 2
compressors shall be started ﬁrst on lag weeks to equalize
run hours between compressors 1 and 2 of the modules
automatically. Compressors shall be staged with a single
compressor per module as required, until all available

modules of the chiller have one compressor running. The
remaining compressors will stage per module, as load
requires. Compressors shall be energized and de-energized by
the program, in an order which will maintain equal run time.

The compressor with most run time will de-energize as the
set point is satisﬁed, and compressor with least run time will
energize, as additional cooling capacity is required.

If a fault is detected the compressor will be disabled and
displayed on the "Master Control Panel" LCD Screen. (Faults
must be manually reset at the chiller).

The Chiller Status and Run Time in hours for each
Compressor shall be shown on the LCD Display on the
“Master Control Panel”. Common Alarm contact and Chiller
Status contact is provided at the panel.

«
...
37
38
39
40
41
...
»

Содержание FLEX 30



















































Отзывы:

Нет отзывов

Похожие инструкции для FLEX 30

Бренд: Yard Machines Страницы: 20

Бренд: Poulan Pro Страницы: 40

Бренд: Poulan Pro Страницы: 44

Бренд: Conair Страницы: 94

Бренд: Trane Страницы: 92

Бренд: Fieldmann Страницы: 27

Бренд: LONCIN Страницы: 32

Бренд: MTD Страницы: 6

Бренд: MTD Страницы: 8

Бренд: MTD Страницы: 12

Бренд: MTD Страницы: 20

Бренд: Clint Страницы: 28

Бренд: Hansa Страницы: 25

Бренд: Weed Eater Страницы: 28

Бренд: FRIULAIR Страницы: 60

Бренд: Yard Machines Страницы: 24

Бренд: Wallenstein Страницы: 68

Бренд: Wallenstein Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды