EXAMPLE: Turn on Lock upon AutoArming and turn off Remote Valet Mode and FACT:
In the following example, we will change the settings of three different features in just one programming session: We will turn on the Lock upon
AutoArming feature to set your vehicle’s power locks to automatically engage whenever the system AutoArms, turn off remote controlled valet mode and
turn off the FACT anti-falsing feature:
1.
Enter program mode
as previously noted (ignition on, enter your valet code, press and hold the
✱
button on the PlainView 2 switch until you hear
a chirp).
2. Since the
Lock upon AutoArming
feature is in column 3, row 2 of the Table, go to column 3 by pressing the blank button on the PlainView 2 switch
three times. Wait for the 3-chirp/column 3 confirmation. Then press the
✱
button twice (you’ll hear a chirp each time you press the
✱
button).
After a brief pause, you’ll hear 2 chirps to confirm that
Lock upon AutoArming
is now on.
3. Since
FACT
is also in column 3, there is no need to reselect column 3. Therefore, you can go straight to the row selection. Select row 4 by pressing
the
✱
button four times. After a brief pause, you’ll hear one chirp to confirm that
FACT
is now off.
4. You’ll note that the
Remote valet mode
feature is at column 2, row 3. To change to column 2, press the blank button twice, then wait for the
2-chirp/column 2 confirmation. Press the
✱
button three times to select row 3. After a brief pause, you’ll hear one chirp to confirm that the
Remote
valet mode
feature is now turned off.
5. To exit the program mode, turn the
ignition off
. You’ll hear 3 chirps to confirm program mode exit.
Reset All Features
If you wish to reset all the user-selectable features to their normal factory presets, you can do so simply by choosing the
Reset all features
selection (column
1, row 7) on the
Table of User-Selectable Features
. If you do so, all features — except the programmed remote controls and your valet code — will be reset
to the factory settings that are indicated in
BOLD
type on the
Table of User-Selectable Features
. To reset all remote controls, use the
Clear all remotes
feature
in column 2, row 6. To reset your valet code, use the
Set a new valet/disarming PIN code
feature in column 2, row 7.
Table of User-Selectable Features
Feature Select
1 blank press
2 blank presses
3 blank presses
4 blank presses
1
✱
press
Add
master
remote control
NOTE 1
Chirps: off/loud/
quiet
(1/2/
3
chirps)
AutoArming: off/
on
NOTE 6
— Add
companion
remote:
arm/disarm (1 then 2 chirps)
2
✱
presses
Personalized Siren Sounds**
NOTE 2
SilentNight:
off
/on
Lock upon AutoArming:
off
/on
NOTE 7
— Add
companion
remote:
trunk release* (2 chirps)
3
✱
presses
Play Personalized Siren Sounds**:
trigger only/
always
(1/
2
chirps)
Valet mode entry/exit via the
remote control: off/
on
AutoArming entry delay:
off
/on
NOTE 7
— Add
companion
remote:
silent arm and disarm (3 chirps)
4
✱
presses
Siren duration:
30
/60/90sec.**
(
1
/2/3 chirps)
AutoStart*:
both off
/both on/temp
only/battery only (
1
/2/3/4 chirps)
FACT: off/
on
NOTE 7
— Add
companion
remote:
timed headlight activation* (4 chirps)
5
✱
presses
AutoLock: off/
on
BlackJax anti-carjacking:
off
/on
Headlight duration: 1sec. – 4.25
min. (
10sec.)
NOTE 5
NOTE 7
— Add
companion
remote:
remote engine starting* (5 chirps)
6
✱
presses
AutoUnLock: off/
on
Clear all remotes
NOTE 3
NightVision: off/
on
/on without post-
parking illumination (1/
2
/3 chirps)
NOTE 7
— Add
companion
remote:
window rolldown/venting* (6 chirps)
7
✱
presses
Reset all features (except remotes
and valet code) to factory settings
Set a new valet/disarming PIN code
NOTE 4
NightVision activation:
lighter
/
twilight/darker (
1
/2/3 chirps)
NOTE 7
— Add
companion
remote:
remote valet mode (7 chirps)
* Requires optional wiring or accessory; ask your Clifford Dealer for details.
**Not available on European models in compliance with EC95/56
NOTE 1: Press button 1 of the new MASTER 5-button remote control. You will hear one chirp.
Immediately press button
1
again. You will hear two chirps to confirm that the new remote control has been added.
NOTE 2: Selection of this feature will cause the system to sound a few seconds of siren sound #1. Press the blank
button to turn on this sound or the
✱
button to turn it off. The system will then sound a few seconds of sound #2.
Repeat: blank=ON,
✱
=OFF for each of the six sounds.
NOTE 3: You’ll hear two chirps to indicate all remotes have been cleared from memory. You must now add
new/existing remotes with the “Add master remote control” feature and/or the “Other vehicle‘s remote” feature.
NOTE 4: Immediately PRESS THE BLANK BUTTON, THEN enter your new code, wait for the two chirps, then turn off the
ignition (you’ll hear 3 chirps to confirm program mode exit). You MUST now turn the ignition back on and then
re-enter your new PIN code. If the LED flashes on, your new code has been accepted. If the LED does not light, the two
codes did not match and the system has reverted to your previous code.
NOTE 5: The timer starts when you select this feature. When the duration you wish has been reached, press the blank
button on the PlainView 2 valet switch (you’ll hear 2-chirps)
NOTE 6: Lets you arm/disarm with a new companion remote control or ANY remote (including 5-button master type)
of a Clifford G4 system on your other vehicle(s). For instance, to set button
✱
of the other car’s companion remote to
arm and disarm your IntelliGuard 9000, select column 4, row 1, then press button
✱
of the other vehicle’s remote
(you’ll hear one chirp). Immediately press button
✱
a second time (you will hear a 2-chirp confirmation). Button
✱
of
the other vehicle’s remote will now arm/disarm your IntelliGuard 9000 on this vehicle.
NOTE 7: The features in this column allow you to control your system with the remote control of a G4 system on your
12
