Automatic malfunction bypass with AutoReMonitoring™
The system automatically bypasses any faulty point and arms all
other
triggers and sensors for the utmost possible protection. If you accidentally arm with
the hood, trunk or a door open, just close it (no need to disarm-and-rearm) and the system will again monitor that point.
Multiple-event TotalRecall™
The system’s memory records the identity of the last eight activated or malfunctioning triggers and sensors, which allows your installer to instantly track down
malfunctions. To identify the triggers and sensors held in the system’s memory, use the following procedure:
1. Remotely arm and disarm while pressing the blank button on the PlainView 2 switch.
2. The LED will flash 1-10 times to indicate the most recently activated point, pause, flash 1-10 times to indicate the second most recently activated
point, and so on.
3. Write down the number of flashes between pauses and refer to the chart above.
With the optional CliffNet Wizard, you’ll see this chronological report right on screen.
Smart prior intrusion attempt alert
If you hear three chirps when you disarm, it means that a trigger or sensor was activated in your absence. When you turn on the ignition, the LED will flash 1-10
times, pause, then repeat the flash cycle 4 more times. Count the flashes in one cycle and refer to the chart above.
User-selectable features
You may set many of the features to your own preferences. Once you’ve changed a few settings, you’ll find that programming the system is so easy that
you can even do it while driving. The system comes with all of its features preprogrammed as noted by the bold type in the
Table of user-selectable features.
To
change any of the settings, use the steps noted below. To restore the feature to its factory setting, just repeat the procedure.
NOTE: For greater programming ease and even more system control, consider the CliffNet Wizard Windows PC
software interface: www.clifford.com/wizard.
How to change a user-selectable feature:
Briefly, here’s how it will work:
•
You will pick a feature from the following Table of User-Selectable Features, noting the feature’s column and row numbers.
•
You’ll enter program mode by entering your valet/disarming PIN code and pressing the
✱
button of the dash- or console-mounted
PlainView 2 switch until you hear a chirp.
•
Press the blank PlainView 2 switch button the same number of times as the column number, then the
✱
button a number of
times equal to the row number.
Step-by-step programming instructions
1. Refer to the
Table of user-selectable features
and make note of the column (across) number and the row (down) number of the feature(s) you wish to
program.
2. Turn the ignition on, or start the engine (skip this step if the engine is running).
3. Enter your valet/disarming PIN code, then press and hold the
✱
button of the PlainView 2 switch for about 4 seconds until you hear a siren chirp.
4.
Select the feature column:
Press and release the blank button of the PlainView 2 switch the same number of times as the column number you wish.
Pause. You will hear the same number of chirps as the column number, audibly confirming your selection.
5.
Select the feature row:
Press and release the
✱
button the same number of times as the row number. You’ll will hear a chirp each time you press to help
you count.
NOTE: You have 5 seconds to enter the row number after selecting the column number. If you wait too long, the system
jumps back to the “Feature Select” position (this is indicated with 3 chirps). If you wait another 60 seconds, the system
will exit program mode.
6.
Pause
. You will hear one or two chirps:
Two chirps = ON, one chirp = OFF
(If there is a
NOTE
for the selected feature, perform the actions noted).
NOTE: Some features, such as AutoStart (column 2, row 4) used with the optional IntelliStart 4 accessory, have
multiple settings. Simply reselect the feature additional times to progress through each possible setting.
7. You may now select another feature or exit program mode:
a. To select another feature in that same column, repeat step 5 within the next 5 seconds (after 5 seconds, 3 chirps mean you are back to the
“Feature
Select”
position).
b. To select a different feature column, go to step 4.
c. To exit program mode, turn the ignition off (you’ll hear 3 chirps and the LED will turn off). If driving, just wait 60 seconds and the system will
automatically exit program mode.
If you make an error, just turn off the ignition and start again.
11
