manualshive.com logo in svg

CLiC-iT RiDER, Инструкция по эксплуатации и техническому обслуживанию, Страница: 9 / 39

Поделиться
Скачать
CLiC-iT RiDER Скачать руководство пользователя страница 9

#

Ratchet Tape

1.500Kg x (?)m. 

Width 35mm

Plastic Tube.

Ratchet tape protector 

D32mm x L160mm

Wood Plank.

Tree protector 

x2

x1

x2

1/2 (inch) Shackle with safety bolt

10-15cm

Ø Tree 

+

+

2.000Kg 

Lifting Sling

Lark´s head

Anchor  

Articulated Arm  

To install an Articulated Arm on a tree a 2000 Kg 
lifting sling is required.

The  remaining  length  after  the  knot  should 
protrude between 10 and 15 cm.

Be sure to measure the diameter of the tree at 
the height where the installation will be made.

The  ratchet  tape  must  be 
located  in  an  inaccessible 
position to the user.

Slings are measured end to end

Required items:  

Anchor Plate for Trees using ratchet tape.

4.4 Articulated Arm installation on trees using lifting sling 

Secure the ratchet with a cable tie

The nut of the shackle must be instaled 
on the opposite side where the arm falls 

4.5 Articulated Arm installation on trees using “Le Clou” system

1/2 (inch) Shackle 

with safety bolt

Reference: CMU 2T MR Bolt shackle

Follow carefully all recommendations of Le Clou safety line user manual

For axial load only

For axial & radial load 

1/2 (inch) 

Shackle with 

safety bolt

M22 1T2 Female 

lifting eye

Nail for Safety line M22

+

Anchor  

Articulated Arm  

1/2 (inch) 

Shackle  ith 

w

safety bolt

Nail for 

Safety line

M22

Junction link

MR ø10-8 CMU

3T150 Type

+

Anchor  

Articulated Arm  

Содержание RiDER








































Отзывы:

Нет отзывов