1941951
V1.6
5 October 2021
UK Instruction Sheet Template – V1.1 – Updated: 20/11/2020
Installation:
This CLIFE Recessed Non-Maintained Emergency Luminaire can be installed on PLASTER or T-BAR
ceilings or used to replace an existing unit.
•
First plan the assembly layout ensuring the battery is kept away from any heat source.
•
Refer Images and Dimensions below for the Cut-out Hole and other dimensions.
•
Use the Spring Clip Mount to mount the Head to the ceiling.
•
Please ensure the control pack and battery is suspended above the ceiling. If the control pack and
battery are to be mounted or placed on top of the ceiling, then please ensure the ceiling is capable
of supporting these elements and in compliance with the relevant regulations with respect to
mounting above/on the ceiling.
•
This luminaire contains non-user replaceable light source and battery.
•
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by
the manufacturer or his service agent or a similar qualified person to avoid a hazard.
•
Terminal block not included. Installation may require advice from a qualified person.
•
Recommended specifications of terminal block for connecting leads:
−
Type of Terminal: Screw Terminal
−
Number of Terminals: 2-Pin
−
Rated Voltage: 250 V
−
Rated Connecting Capacity: 10A
•
If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four
Segment Marking on the product will include an ‘’F’’ in third segment block.
Networking:
When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the
relevant Smart Node PCA.
Images and Dimensions:
Head depth:
40mm including connector
Head Diameter:
95mm diameter
Cut-out Hole:
85mm diameter
Adaptor Ring:
145mm diameter, suits 125mm hole
Control gear:
232mm (L) x 51mm (W) x 42mm
Battery pack:
165mm (L) x 38mm (W) x 35mm (H)
145mm Adaptor Ring
Note:
This luminaire (with reinforced insulation between control/LED terminal and AC supply) contains non-
user replaceable light source and battery - to be replaced (if required, refer installation instructions for
battery replacement) by Clevertronics service personnel/agents or a registered electrician.
Battery Replacement:
1. Prior to any work, isolate the power to the luminaire that requires battery replacement.
2. Remove the cord anchor securing battery cable by removing screw under driver.
3. Remove the Battery Connector from the Emergency Driver.
4. Replace battery, reconnect battery connector to Emergency Driver.
5. Carefully reinstall the cord anchor ensuring the lamp cable and battery cable are not pinched or
damaged.
Testing Procedure:
When the unit is connected to the un-switched active, it must be allowed to charge the battery for at
least 24 hours. The emergency lamp only illuminates during a power fail. Conduct the following tests:
•
The emergency lamp must illuminate for at least 180 min after disconnection from the mains. If the
unit fails to illuminate for the requisite time, remedial action must be taken to repair the situation
and once completed, the unit must pass a subsequent test.
•
Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.
•
Release the Test Button or Switch On Mains Supply, check that the emergency lamp is Off (Non-
maintained operation).
Below are a list of common problems and their possible causes:
Fault: The Green LED indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected.
Test Switch for damage.
Fault: Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency mode, but only stays on for a short period.
Check: Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The Li-ion battery in the Exit & Emergency Unit has been selected to give
excellent long life performance in a controlled IEC 60598-2-22 testing environment. Excessive battery
cycling will reduce through-life performance and may lead to premature battery failure. Battery warranty
claims, as a result of such abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
https://clevertronics.co.uk/product-warranty-statement/
