Clemco CMS-4 Скачать руководство пользователя страница 28

Страница: 28 / 29

CMS-4 IN-HELMET CARBON MONOXIDE MONITOR

Page 23



www.clemcoindustries.com



Manual No. 29872

7.0

TROUBLESHOOTING

The troubleshooting table describes error messages,
symptoms, probable causes, and recommended action
for problems encountered with the CMS-4.

NOTE:  If  the  monitor  does  not  display  menu  items  that
are noted within these instructions, repeat the process. If
after  repeating  the  process  the  monitor  still  does  not
display  the  correct  menu  item,  return  the  monitor  to
factory settings, per Section 4.4.

Symptoms

Probable Causes

Recommended Action

The LCD is blank.

The monitor may have been turned
off.

1. To turn on the

monitor

, press and briefly hold

POWER/MODE.

The battery was inserted
backwards.

1. Reinstall the battery in the correct orientation.

Battery may need to be replaced.

1. Check battery ICON

for remaining battery life.

The battery cover may not be
completely closed.

1. Be sure the battery cover is completely closed and

that the screw is tight.

2. If the difficulties continue, contact the Clemco distributor

the monitor was purchased through for further instruction.

The LCD shows an
abnormally high reading,
but other gas detection
instruments do not.

Charcoal filter may need to be
replaced.

1. Replace the charcoal filter.

The CMS-4 may need to be
recalibrated.

1. Recalibrate the

monitor.

2. If the difficulties continue, replace the sensor and

calibrate.

The sensor may need
replacement.

1. Recalibrate the monitor.
2. If the difficulties continue, replace the sensor and

calibrate.

Calibration fails.

The calibration gas values may not
match the cylinder gas
concentration.

1. Make sure test gas and gas value are 25 ppm.

Refer to Sections 5.6 and 5.7

2. Make sure the CMS-4 has been properly set up

for calibration.

3. If the fail condition continues, replace the

sensor.

4. If difficulties continue, contact the Clemco

distributor the monitor was purchased through for
further instruction.

The sample gas is not reaching the
sensor because of a bad
connection.

1. Check all calibration tubing for leaks or for any bad

connections.

The calibration cylinder may be out
of gas or is outdated.

1. Verify that the calibration cylinder contains an

adequate supply of fresh test sample.

The sensor may need replacement.

1. If the fail condition continues, replace the sensor.
2. If difficulties continue, contact the Clemco distributor the

monitor was purchased through for further instruction.

Heart symbol at the top of
the screen becomes
steadily on or disappears.

A microprocessor error has
occurred.

1. Contact the Clemco distributor the monitor was

purchased through for further instruction.

Monitor does not display
menu items as noted
within the instructions.

Factory settings accidentally
changed.

1. Return to factory default settings per Section 4.4.

Содержание CMS-4






























Результаты поиска

Содержание CMS-4

Отзывы:

Похожие инструкции для CMS-4

Бренды по названию

Популярные бренды

Clemco CMS-4, Руководство по эксплуатации

Результаты поиска

Содержание CMS-4

Отзывы:

Похожие инструкции для CMS-4

Бренды по названию

Популярные бренды