Clemas & Co TENNANT F8 Скачать руководство пользователя

Страница: 4 / 7

EN English

F3/F3+/F8/F12 9002026 (04

11)

Correct Use

All single

disc machines are intended exclusively for

use in building interiors.

Any use beyond this is considered incorrect. The
manufacturer accepts no liability for any resultant
damage; the user alone bears the risk.

Correct use also includes adherence to the operating,
servicing and maintenance conditions recommended
by the manufacture.

The relevant accident prevention regulations as well
as all the generally acknowledged safety and working
practices must be followed.

Unauthorized modifications to the machine exclude
the manufacturer’s liability for resultant damage.

Before machine use, floorcoverings must be tested for
suitability for this cleaning process.

Pay attention to the area compression of point

elastic

floors, e.g. in gymnasiums

The manufacturer accepts no liability for damage to
equipment and to the floor being cleaned from using
the wrong brushes and cleaning agents.

Machines may not be used in combination with an
extension cord.

Product Liability

The operator’s attention is drawn explicitly to the fact that the
machines may only be used for their intended purpose. If the
machines are not used for their intended purposes, the user
must accept full responsibility. Any liability of the manufacturer is
thus excluded.

Sources of Risk

WARNING: The single

disc machine is not suitable

for cleaning surfaces which release

healthhazardous dusts and liquids. Do not use the

machine on steps.

WARNING: This machine is only intended for use on

level surfaces with a maximum gradient of up to 2

WARNING: This machine is not approved for use on

public paths and roads.

WARNING: Use only the brushes provided with the

appliance or those specified in the instructions. The

use of other brushes may impair safety.

WARNING: When the machine is stationary, the

brush unit must be immediately switched off to

prevent damage to the floorcovering.

WARNING: During transportation in lifts, the

currently valid user instructions and safety

regulations and particularly those concerning

maximum loading must be observed.

Machine operation position

The machine operation position is behind the machine.

Approved maintenance staff

The single

disc machine may only be serviced and repaired by

persons with technical and legal authorization.

Cleaning agents

When using cleaning and care agents, the
manufacturer’s danger warnings must be followed and
protective goggles and clothing must be worn.

Only use low

foaming, non

combustible cleaning

agents which do not contain generally
health

hazardous substances.

Explicit reference is made to the risks of using highly flammable,
combustible, toxic, health

hazardous, corrosive or irritant

substances.

Machine assembly and operation

Initial operation

Delivery, instruction on safety procedures, handling
and maintenance and initial operation are generally
carried out by our authorized specialist.

If this is not the case, the operator is responsible for
instructing machine users.

Please remember that the voltage in the building
being cleaned must concur with that given on the
machine’s type plate.

Assembly instructions

The motor head and bar are supplied separately
packed.

First release the hexagon socket screws in the shaft
adjustment unit (6).

Then feed the bar (7) gently as far as it will go into the
shaft adjustment unit (6).

Align the handle bar (1) parallel with the wheels (9),
so that the open side of the housing of the top shaft
element (3) is facing to the rear.

Then tighten the hexagon socket screws again.

Wind the electric cable around the handle bar (1) and
cable hook (8).

Preparation for use

Grasp the handle bar (1) with both hands and tip the
machine until it is resting on both wheels (A).

Then wheel the machine to its place of work and plug
the electric cable into the power supply.

Set the desired rpm, using the switch mounted at the
motor housing (only for F8 Duo speed)

Lay the accessories (11), i.e. brush or drive plate with
pad, on the floor.

Now tip the machine back onto the wheels and push it
over the brush (or drive plate) until the drive star and
brush flange are vertically aligned. Lower the machine
onto the brush (B).

Then squeeze the shaft adjustment lever (5) and
lower the bar (7) into its working position. Both arms
should be extended loosely downwards (C).

Align the machine horizontally above the working
element (brush or drive plate), press the switch lock
(4) and press the brush motor switch (2) briefly.

The accessory automatically engages.