Cleco 48EAE105AH4, Инструкция по эксплуатации

Страница: 8 / 136

Page 8
TM12-1105-LG1
08/25/2017 EN
b) Never use an electric tool with a defective switch. An
electric tool that can no longer be switched on and off is
dangerous and must be repaired.
c) Pull out the connector from the nutrunner
control and/or the tool cable from the
socket/receptacle and/or remove or
disconnect the battery before altering
tool settings, changing accessories or
putting the tool back down again. These
precautionary measures prevent the electric
tool from restarting accidentally.
d) When not in use, keep electric tools out of the reach
of children. Do not allow anyone to use the device
if they are not familiar with its operation, or have
not read the instructions for use.
Electric tools are
dangerous if used by inexperienced people.
e) Treat electric tools with care. Check to ensure that
moving parts function perfectly and do not jam. Also
check to ensure that no parts are broken, or damaged
to such an extent that the function of the electric tool
is impaired. Arrange for damaged parts to be repaired
before using the device. Poorly maintained electric tools
have been the cause of many accidents.
f) Keep cutting tools sharp and clean. Carefully
maintained cutting tools with sharp edges jam less
frequently and are easier to guide and operate.
g) Always use electric tools, accessories and impact
tools in accordance with these instructions. Also
pay attention to ambient workplace conditions and
the nature of the work being carried out. Dangerous
situations can arise if electric tools are ever used for any
application other than the one intended.
5 Service
a) Always arrange to have your electric tool repaired by
suitably qualified 1) technical specialists, and always
use genuine spare parts. That will ensure that you
maintain the high safety standard of your electric tool.
Specific safety instructions for Hand-Held
Electric Nutrunner
1 Electrical safety
a) Ensure that the PE connection has a low-current source.
b) Use a mains transformer for cable lengths in excess of
66 ft. (20 m). Max.164 ft. (50 m).
2 Safety of persons
a) 18ET/EC, 48ET/EC series: By accidentally pressing the
Start key, the chuck (bit holder) can rotate in the output
drive (e.g. when putting down the tool). This can crush
or even sever fingers. Never insert your fingers in the
chuck. To change the bit, first disconnect the tool cable.
b) The wearing of gloves is prohibited.
c) Grip tool firmly in your hand. Be prepared for rapid
changes in reaction torque.
d) When using the tool in confined spaces and with torques
in excess of
• 3 ft.lbf (4 Nm) for straight tools
• 7 ft.lbf (10 Nm) for pistol/gun tools
• 44 ft.lbf (60 Nm) for angle tools
always use a reaction bar. When in use, never place your
hand on the reaction bar.
e) Check that the suspension bail is properly secured to the
balancer.
Tools with integrated barcode scanner
--------------------------------------------------------------
Class 2 laser product
Class 2 laser scanners use a laser diode that
produces a low-power visible light beam that
is comparable to a very bright source of light,
such as the sun.
Doing so can cause damage to the eyes.
--------------------------------------------------------------
a) Do not look into the laser beam.
b) Repair faults on optical parts at once.
c) Changes to the barcode scanner are prohibited.
d) Take defective tools out of operation immediately.
3 Use and handling of a Hand-Held Electric
Nutrunner
a) Only use screw bits for machine-controlled tools.
b) Make sure that the screw bits are securely inserted.
c) Do not attach screw bit to the screw head at an angle.
d) Never use a high-pressure cleaner/jetter to clean the tool.
e) Do not immerse tool in cleaning agent.
4 Designated use
This product is part of the APEX tightening system and is
designed exclusively for fastening and releasing threaded
fasteners.
→ Only use in conjunction with a control series mPro400GC,
accessories and tool cable supplies by Apex Tool Group.
→ Do not use as a hammer or for re-bending.
→ Do not open it or modify it structurally.
→ Do not use it in areas where there is a risk of explosion.
5 Ambient Conditions
Function Temperature
Relative
Humidity
Working
Height
Transport /
Storage
-13°F to +158°F
(-25°C to +70°C)
Ope32°F to +113°F
(0°C to +45°C)
0…90%
non-condensing
up to 9800 ft.
(3000 m)
above sea level
-----------------------------------------------------------------------------------------
1. Due to their vocational training, knowledge, experience and
understanding of the circumstances involved in this kind of
work, suitably qualified personnel are able to identify potential
hazards and to initiate appropriate safety precautions.
Qualified personnel are obliged to follow the regulations, i.e.
to obey the rules.