background image

Operating Instructions

4-4

750-136

Model WB Electric Boiler Manual

4.2 — Maintenance Schedule

4.2.1 — Weekly Procedure

Tighten the main supply lugs every 24 hours during the first week of operation.

4.2.2 — Quarterly Procedures

While the boiler is operating, lower the temperature setting drastically on the temperature control and listen for 
the magnetic contactors to open. Then return the setting to normal and again listen for the magnetic contactors 
to operate.

Turn off the control pilot switch and the main power supply switch. This is done as a safety measure to prevent 
accidental turn-on of power.

Tighten all the electrical connections that could have loosened due to heat expansion and contraction. Pay par-
ticular attention to the main lugs that receive the power circuit. Examine all the relays and the magnetic contac-
tors for pitting, corrosion, burned or welded contacts, or inoperative 120 volt coils. Inspect for blown fuses or 
discoloration of fuse clips, which would indicate a loose fit. Correct malfunctions as required.

If all the elements have been operating normally and each element bank draws its rated current or amperage, 
where:

AMPS (3-phase) =      Watts   
                           Volts x 1.73

or

AMPS (single phase) = 

 

  Watts  

                                     Volts

no further element tests are necessary. However, if there is a low or unbalanced amp reading, further tests with 
an ohmmeter may be necessary to detect the open or shorted element(s) in the group. To test individual ele-
ments for continuity with an ohmmeter, the jumpers between elements must first be removed. 

NOTE:

 Only personnel who have a working knowledge and understanding of this equipment should have access to 

the control cabinet.

Lockout and disconnect the boiler’s main power to avoid the hazard of electrical shock, which could result in serious 
personal injury or death.

When checking the element terminal connections, use wrenches on both nuts to avoid twisting the terminal stud and 
damage to the equipment.

!

Warning

!

Caution

Содержание WB





































Отзывы: