ClearSpan Round Style Mini Garage Скачать руководство пользователя

Страница: 14 / 21

CLEARSPAN

™

GARAGES & STORAGE SHEDS

Revision date: 08.09.10

4. Once the main cover is pulled into position, center the

cover on the frame and remove the ropes. Loosely

secure the ends of the cover to the ratchets attached to

the front and back end panel conduits.

ATTENTION:

Do not tighten the straps at this time

5. Place the D-ring straps on the ground along one side

of the shelter beside the rafters identified by the arrows

below. Place the plain straps and ratchets

on the

opposite side of the shelter

at the same rafters as the

D-ring straps.

ATTACH MAIN COVER

Gather the Parts:
• Main cover (with conduits already inserted)
• Ropes long enough to reach over the frame (provided

by customer)

•  D-ring Straps and Plain Straps
•  Tek screws and Fender washer
•  Box cutter or utility knife

Assembly Procedure
1. To pull the cover over the frame, attach a rope to each

end of the cover conduit. Wrap the rope around the

conduit a few times to prevent it from slipping off.

2. With all ropes attached conduit, lift the conduit and

carry the cover toward the base of the frame.

3. Toss the ropes over the frame and pull the cover into

position. One person is required at each rope.

3. After assembling the cover conduits, locate the main

cover and unfold it on a clean, smooth surface near the

frame. Unfold the main cover with the inside surface

facing up.

4. Locate the cover ends with strapping and align with the

front and back of the shelter.

5. Insert the cover conduits into the pockets of the main

cover.

Cover

Ends with

Strapping

Cover Conduits

NOTE:

Shelter shown above may be a different length

than actual model.

NOTE:

Depending on the cover length, it may be

necessary to attach additional ropes to the conduit

between the end ropes. To do this, cut a small opening

in the cover pocket and tie the rope around the conduit.

DO NOT cut through the main cover.

Cut through the

conduit pocket only.

6. On the side of the shelter where the D-ring straps are

located, lift the main cover skirt and cut a slit through

the main cover pocket at the rafters identified by the

arrows above.

PREPARE MAIN COVER (CONTINUED)

Cover

Conduit

Ropes

Содержание Round Style Mini Garage






















Результаты поиска

Содержание Round Style Mini Garage

Отзывы:

Похожие инструкции для Round Style Mini Garage

Бренды по названию

Популярные бренды

ClearSpan Round Style Mini Garage, Руководство пользователя

Результаты поиска

Содержание Round Style Mini Garage

Отзывы:

Похожие инструкции для Round Style Mini Garage

Бренды по названию

Популярные бренды