ClearSpan 108299F Скачать руководство пользователя

Страница: 15 / 25

CLEARSPAN

™

POLY BUILDINGS

Revision date: 05.19.09

ATTACH MAIN COVER (CONTINUED)

SHELTER CARE AND MAINTENANCE

Proper care and maintenance of your shelter is important.

Check the following items periodically to properly maintain

your shelter.
• Regularly inspect the main cover and panels (if

equipped) to see that these remain tight and in proper

repair.

• Check connections and all fasteners to verify that they

remain tight.

• Do not climb or stand on the shelter at anytime.
• Remove debris and objects that accumulate on the

shelter. Use tools that will not damage the cover when

removing debris.

• Remove snow to prevent excess accumulation. Use

tools that will not damage the cover when removing

snow.

NEVER ALLOW SNOW TO ACCUMULATE ON

THE ASSEMBLED SHELTER.

• Check the contents of the shelter to verify that

nothing is touching the cover, side panels, or the end

panels that could cause damage.

• Check the anchoring system to ensure that all

components are tight and in good repair.

• Review the MUST READ document for anchoring

requirements.

• Inspect all building components regularly. Replace all

worn or damaged parts promptly.

• If the shelter is disassembled and moved, inspect all

parts and connections before reassembling.

• For replacement or missing parts, call 1.800.245.9881

for assistance.

NOTE:

With the exception of Truss Arch buildings,

ClearSpan™ shelters and greenhouses

do not

have any

tested loading criteria.

NOTE:

DO NOT cut through the main cover.

Cut

through the conduit pocket only.

9. Thread the strap ends into the ratchet and slightly

tighten.

7. Lift the cover skirt and cut a slit in the cover conduit

pocket at the rafter position.

8. Insert a 3' section of strap through the slit and around

the cover conduit.

NOTE:

It may be necessary to remove excess strap if it

binds up in the ratchet.

10. Repeat the steps for the remaining ratchets.
11. Using additional help (if needed) tighten the main

cover beginning with the ratchets along the sides of the

shelter frame.

12. After the side ratchets are tightened, return to the front

and back end ratchets and tighten.

NOTE:

Loosen the ratchets if needed to remove

excess strap and retighten. Loosen all ratchets if

needed to reposition the main cover on the frame and

then retighten the ratchets.

13. Fold the skirt of main cover down to complete the

installation.

14. Complete and return all warranty information.
15. Continue by reading the care and maintenance

information.

Содержание 108299F


























Результаты поиска

Содержание 108299F

Отзывы:

Похожие инструкции для 108299F

Бренды по названию

Популярные бренды

ClearSpan 108299F, Руководство пользователя

Результаты поиска

Содержание 108299F

Отзывы:

Похожие инструкции для 108299F

Бренды по названию

Популярные бренды