ClearSpan 108294F Скачать руководство пользователя страница 7

Страница: 7 / 25

CLEARSPAN

™

POLY BUILDINGS

Revision date: 05.19.09

LAY OUT THE BUILDING SITE

After the site is prepared, identify the location of the shelter

corners to help square the frame after it is assembled.

Taking these steps

before

assembling the shelter saves

time and ensures that the structure is positioned as

desired. The following procedure is a suggested method.

Its use depends on the size of the shelter, shelter

application, the footings, and the method used to anchor

the shelter.

SQUARE THE SITE

1. Identify a corner where a building rafter will be

positioned, drive in a stake, and string a line the exact

width of the building and stake in place. (Width of the

rafter is measured from center-to-center of the rafter

legs.)

2. Sting a line at least as long as the building from the first

stake at 90°.

NOTE:

A transit can be used to ensure an accurate 90°

angle, or the 3-4-5 rule can be used. Refer to diagram.

Using multiples of 3-4-5 such as 6-8-10 or 12-16-20

helps to maintain an accurate 90° angle.

3. After squaring the position of the building and placing

a stake at all corners, string a line between the stakes

to mark the base of the building.

4. Next, paint or mark a line on the ground using the

strings between the stakes as guides.

Space below is reserved for customer notes.

NOTE:

If a baseboard

is used, drill holes

through the board at

evenly-spaced intervals

along the length of

the board. Drive a rod

through each hole and

into the site to prevent

the boards from shifting

and to maintain the

on-center width of the

building.

Actual rafter is not shown.

Baseboard

Rod or Ground

Stake

NOTE:

Setting

customer-supplied baseboards

on the

site in the correct positions is another way to prepare

for the frame assembly.

The baseboards can be "pinned" in place using rods

driven into the site (non-concrete) through evenly-

spaced holes drilled in the baseboard. This prevents

the baseboards from shifting during assembly.

Building width is measured on-center.

5. After marking the outline of the building, continue with

the rafter assembly instructions.

Содержание 108294F


























Результаты поиска

Содержание 108294F

Отзывы:

Похожие инструкции для 108294F

Бренды по названию

Популярные бренды

ClearSpan 108294F, Руководство пользователя

Результаты поиска

Содержание 108294F

Отзывы:

Похожие инструкции для 108294F

Бренды по названию

Популярные бренды