manualshive.com logo in svg

ClearSpan 106185, Инструкция по эксплуатации, Страница: 24 / 41

Поделиться
Скачать
ClearSpan 106185 Скачать руководство пользователя страница 24

CLEARSPAN

™

 GREENHOUSES

24

Revision date: 07.22.11

After the holes are drilled, temporarily insert the 

4. 

carriage bolts through the bracket and tube to hold the 

bracket in place and mark the location of the adjusting 

bolt hole on the top of the door frame tube.
Using a 1/2" drill bit, drill a hole through the door frame 

5. 

tube. The hole allows the adjusting bolt of the roller 

assembly to extend through the tube if needed.

Small 

Angled 

Bracket

Flat Plate

Flat Plate is placed on top 

of the door frame with bolts 

pointing up to receive the 

nuts.

Assemble the flat plate and brackets as shown below.  

6. 

 

 

NOTE:

 Assembly is shown looking from the front or 

outside. Insert the mounting carriage bolts for the 

brackets 

from the back to prevent damage

 to the 

polycarbonate panels on the end wall when the door is 

used. 

 

Brackets must be assembled as shown so that the 

holes in the brackets are aligned.

Adjust the flat plate and brackets to align the adjusting 

8. 

nut with the pre-drilled 1/2'' hole and tighten bolts.  

 

NOTE:

 The adjusting nut must turn freely between 

the brackets and the top of the door frame. Tighten all 

bolts.
Install the adjusting bolt and roller assembly. Position 

9. 

the notch of the roller assembly up and away from the 

door.

Repeat the steps to assemble and attach the remaining 

10. 

roller assembly to the door frame. Photo below shows 

the attached roller assembly as seen from the outside 

or front. 

ASSEMBLE AND ATTACH SLIDING DOORS (continued)

Do not tighten the small bolts at this time. you will need 

to adjust the brackets when the rollers are installed.
Place the adjusting nut on the door frame and set the 

7. 

assembled brackets and flat plate over the nut. 

After attaching the roller assemblies, turn the door 

11. 

frame on its side and drill a hole in the bottom of the 

frame tube. (This hole will allow water drain from inside 

the door frame if it finds its way through the adjusting 

hole at the top of the frame. 

 

NOTE:

 Each box includes two (2) roller assemblies for 

each door frame.
Repeat the steps to assemble and attach the remaining 

12. 

roller assemblies.

Содержание 106185










































Отзывы:

Нет отзывов