8.
P-Link (Peripheral Link) In and Link Out Ports
:
»
The P-link ports provide Power, Audio & Control for peripheral devices such as the Beamforming Mic
Array 2 and DIALOG 20 2 Channel Wireless Receiver�
»
The P-Link In Port is also used as PoE-In Port, so this port can be used to connect PoE Injector to provide
power to peripheral devices�
»
One PoE injector can provide power for up to 3 peripheral devices�
»
Up to 6 peripheral devices can be connected to the same P-Link chain� You can connect 3 each of the
Beamforming Mic Array 2 units + DIALOG 20 units per CONVERGE Pro 2 unit, or 6 Beamforming Mic
Array 2 units with two CONVERGE Pro 2 units�
»
It uses a standard (not crossover) patch cable�
»
LEDs adjacent to each port indicate connection status and packet traffic activity�
»
Maximum cable length is 200 feet�
9.
C-Link In and Link Out Ports
: Two RJ-45 E-bus (expansion bus) connectors used to connect multiple
CONVERGE Pro 2 units together to create a site� You can connect any combination of CONVERGE Pro 2
units, where the total number of microphone inputs does not exceed 96� Maximum cable length is 150 feet
using solid core, factory terminated Category 5e or 6 cable�
10.
VoIP
: A RJ-45 10/100Mbps auto-sensing Ethernet port connecting to 5 lines, with each line supporting
up to 5 calls�
11.
Dante Primary & Secondary Ports
: Two RJ-45 100/1000 Mbps Ethernet connectors for connecting to
primary and secondary Dante networks� Maximum cable length is 328 feet�
12.
2-Channel Speaker Posts (only 48T)
: Two post/banana plug connectors used to connect an external
speaker (4Ω – 16Ω). Internal power amplifiers eliminate the need for an external power amplifier.
13.
Telco Line Port
: One RJ-11 connector telephone port� The Telco port connects an analog telephone line
to CONVERGE Pro 2 devices�
NOTE
: The Telco port is not available for use when the telephone hybrid is off-hook�
CONFIGURING THE CONVERGE PRO 2
CONVERGE Pro 2 CONSOLE software is required for configuring CONVERGE Pro 2 units� Configuration
instructions can be found in the CONVERGE Pro 2 Installation and User Manual at www�clearone�com�
APPLICATION PROGRAMMER’S INTERFACE
The CONVERGE Pro 2 Serial Command Guide is available for viewing or download at www�clearone�com�
COMPLIANCE
Details on compliance can be found on the ClearOne website under “Resource Library”�
WARNING
: Use the
C-Link In
and
C-Link Out
ports with CONVERGE Pro 2 Devices ONLY� Connecting
ANY other devices to the C-Link In and C-Link Out ports, including CONVERGE Pro or Beamforming
Microphone Array products will result in severe equipment damage�
© 2016 ClearOne, Inc� All rights reserved�
Information in this document is subject to change without notice� QSG-0032-001 Revision 1�0 AUGUST 2016
HEADQUARTERS:
Salt Lake City, UT USA
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
Tel:
801�975�7200
Toll Free:
800�945�7730
Sales:
800�707�6994
Fax:
801�303�5711
e-mail:
sales@clearone�com
Europe
Tel:
+44�1454�616�977
UK Tech Support:
+44�0800�680�0682
e-mail:
global@clearone�com
Asia Pacific
Tel:
+86�138�23287825
Tech Support:
+86�18420152949
e-mail:
global@clearone�com
Middle East
Tel:
+
91�9930782195
e-mail:
global@clearone�com
TechSales
Tel:
800�705�2103
e-mail:
techsales@clearone�com
Technical Support
Tel:
800�283�5936
Tel:
801�974�3760
e-mail:
tech�support@clearone�com
CLEARONE LOCATIONS
7
