Clear-Com RCV-2 Скачать руководство пользователя страница 19

W i r e l e s s   I F B / C u e   S y s t e m

5 - 1

       SPECIFICATIONS

UPX-10 WIRELESS TRANSMITTER

Product Description

VHF audio transmitter 

Frequency Control

Single frequency, crystal controlled 

Frequency Stability

±0.005%

Operating Frequency Range

169-216 MHz

RF Power Output

50 mW, maximum

Modulation

Direct FM, 45KOF3E

Maximum Deviation

±7.5 kHz

Deviation Limiter Type

Frequency-compensated active rectifier, voltage-controlled 
amplifier

Deviation Limiter Range

20 dB after limiting starts 

Audio Input

3-pin female XLR (mic/line mode)
Pin 1: ground
Pin 2: audio+ 
Pin 3: audio -

Intercom Mode

Pin 1: ground
Pin 2: +VDC
Pin 3: audio 

Audio Input Level Select

Rear-panel mounted slide switch

Audio Input Level

Line: -10 to +20 dBu
Mic:  -40 to -10 dBu

Audio Input Adjust Range

30 dB

Audio Frequency Compensation

Low: ± 10 dB; High: ± 10 dB

Front Panel Controls and Indicators

Power on/off switch
Power-on LED
Audio input level adjust
VU meter (8-segment LED)

Rear Panel Controls and Indicators

Audio input connector (3-pin XLR female)
Audio processing switch
Audio input level switch
Frequency compensation: high and low 
DC power input
RF output (S0-239)

Power Required

12–24 VDC, 300 mA max, negative ground

Power Supply Provided

Wall-mount, 12 VDC, 500 mA, unregulated (120 VAC 
standard, 240 VAC optional)

Packaging

19 in. (48 cm) rack-mount
17 in. W x 1.72 in. H x 5.1 D, excluding detachable rack-mont 
ears
43 cm W x 4.4 cm H x 13 cm D, excluding detachable 
rack-mount ears 

Weight

3.2 lbs. (1.5 kg) without power supply 

5

Содержание RCV-2

























Отзывы: