Clean Water Systems Pro-OX 7800 Скачать руководство пользователя страница 2

Страница: 2 / 13

Clean Water Made Easy

www.cleanwaterstore.com

Table of Contents

Packing List ................................................................................................................................................ 3

Carbon Filter 1.0 cubic foot size ............................................................................................................. 3

Carbon Filter 1.5 cubic foot size ............................................................................................................. 3

Carbon Filter 2.0 cubic foot size ............................................................................................................. 3

Carbon Filter 2.5 cubic foot size ............................................................................................................ 3

Pre-Installation .......................................................................................................................................... 4

Best Practices for Piping & Drain Installation ............................................................................................. 4

How Your Carbon Filter Works .................................................................................................................. 5

Fig 1 - Carbon Filter Tank Water Flow ............................................................................................... 5

Fig 2 - Typical Carbon Filter 7800 piping installation with ball valve and hose bib after the filter ...... 6

Fig 3: 7800 from the rear showing the inlet (left) and outlet (right) end-connector fittings 3/4” or 1”
NPT in Noryl plastic. Brass end-connectors are also available for connecting to copper tubing. ........ 7

Fig 4 7800 Bypass and Service Positions ........................................................................................... 7

Assembly and Installation Instructions ...................................................................................................... 8

Fig 5: 7800 By-Pass and Pipe Connectors ........................................................................................... 9

Initial Programming: ................................................................................................................................ 10

Troubleshooting the 7800 Carbon Filter .................................................................................................. 12

Содержание Pro-OX 7800














Результаты поиска

Содержание Pro-OX 7800

Отзывы:

Похожие инструкции для Pro-OX 7800

Бренды по названию

Популярные бренды

Clean Water Systems Pro-OX 7800, Инструкция по установке и запуску

Результаты поиска

Содержание Pro-OX 7800

Отзывы:

Похожие инструкции для Pro-OX 7800

Бренды по названию

Популярные бренды