Clean Water Systems J-PRO-22 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 16

background image

J-PRO-22 Alum Guide Rev 0021622 Page | 10

Install Suction Tubing from Pump to Solution Tank

Connect hard tubing from foot valve in Solution Tank to Inlet/ Suction side of metering pump

1.

Measure the tubing from the outside of the solution tank to ensure it will be 2-3” from the
bottom of the solution tank.

2.

Do not allow weight to sit at the bottom of the tank. Connect tubing to the foot valve and put
the ceramic weight on.

3.

Run the tubing up through the hole and connect to the Inlet/ Suction side of pump

Suction

Ceramic

Connector

Foot

«
...
8
9
10
11
12
...
»

Содержание J-PRO-22

















Отзывы:

Нет отзывов

Похожие инструкции для J-PRO-22

Бренд: Jura Страницы: 11

ECOSOFT MO10000

Бренд: BWT Страницы: 87

PuraShield 1000

Бренд: Purafil Страницы: 8

Бренд: Schenker Страницы: 44

Бренд: Fiap Страницы: 22

Water Quality System EQHP-TWIN 108SP

Бренд: Bunn Страницы: 2

Filtermax Basic

Бренд: IONFILTER Страницы: 2

Бренд: Clack Valves Страницы: 26

BioPressure 7000

Бренд: ubbink Страницы: 64

Бренд: CDA Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Saeco AquaClean CA6903/47

Бренд: Philips Страницы: 2

WP3822 Micro X-Pure

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 8

Saeco AquaClean CA6903

Бренд: Philips Страницы: 9

Бренд: Philips Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды