manualshive.com logo in svg

Clean Water Systems 5900e-AIR, Инструкция по установке и запуску

Поделиться
Скачать
Clean Water Systems 5900e-AIR Скачать руководство пользователя страница 14

Air Charger Sulfur Filter 5900e-AIR Installation & Startup Guide 

Page 14 

www.cleanwaterstore.com 

Rev 082616 

 

 
5. 

To Set the Number of Days between Air-Draw Cycles (d) Press the Set/Change Button

 

1) Set to 1 day, to regenerate the system with new air daily.    

Example [ d - 01] 

2) During this process, the valve will use a little bit of water to create suction in order to 
regenerate the air, and will make some noise during this cycle. However, the valve will still 
backwash on the days that you have programmed it to. 
2) If Value Set to 0, Air-Draw is Turned Off, but an Air Cycle will still be Completed when a 
Regeneration Cycle Occurs. If the Number of Days between Air-Draw Cycles is set to a Higher 
Number of Days than the Number of Days between Regeneration Cycles, it will have no effect. 
 

6. To exit menu press the Menu/Enter button 

Note: If no buttons are pressed for 60 seconds or longer the menu will automatically be 
exited. 
 

Next you will need to set the Master Programming to be used as an Air Charger Sulfur Filter 
5900e-AIR filter, continue on to the Master Programming to finish the programming 
instructions. 

Master Programming Mode: 

Entering Master Programming Mode 

-To enter Master Programming Mode press and hold both buttons for 5 seconds. 

 
1. Regeneration Time (r) 

Press the Menu/Enter Button. The next display viewed is the option setting for 
Regeneration Time. It is identified by the letter ‘r’ in the left digit. Set the desired time 
of day that a regeneration may occur, if required. We recommend setting the system to 
backwash at 2 AM, or at any time that it is unlikely that any water will be used. The first 
digit(s) indicates the Hour and the other digit indicates A.M. or P.M.. 

Example: 2 A.M. regeneration time - [ r 2A ] (factory setting) 

 

3. Regeneration Cycle Step Programming (2)(3)(4)(5) 

Step 1, the air release, is not programmable, and therefore will not be displayed for 
programming. Each display is used to set the duration time in minutes for that specific 
step in a regeneration cycle. A step # will turn on for the regeneration cycle step being 
programmed. Regeneration steps are skipped by setting the display to 0 as shown 
below: 
 
Examples: Regeneration Cycle Step #2 - 10 minutes - [ 2 - 10 ]  
Regeneration Cycle Step #3 - skipped - [ 3  - 0 ] 
 
Set each step according to the values below, appropriate for an Air Charger Sulfur Filter 
5900e-AIR filter: 
 

Содержание 5900e-AIR




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды