background image

Repair or Warranty Contact

 

Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084

WGP-0 

www.DustlessMadeSimple.com

 • 

[email protected]

 

Page 3

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING

To reduce the risk of fire, electric shock, or injury:

• 

Do not

 leave appliance when plugged in. Unplug from outlet when not in use and before servicing.

•  This unit is to be used only indoors and in a dry location.
•  Use only as described in this manual. Use only manufacturer’s recommended attachments.
• 

Do not

 use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, 

or dropped into water, return it to a service center.

•  Handle provided on power head is used only for removal of power head during maintenance.
•  Before separation of power head from tank, users must disengage draw latches on tank. 
• 

Do not

 pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. 

• 

Do not

 run appliance over cord. Keep cord away from heated surfaces.

• 

Do not

 unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• 

Do not

 handle plug or appliance with wet hands.

• 

Do not

 put any object into openings. 

Do not

 use with any opening blocked; keep free of dust, lint, hair, and anything that may 

reduce air flow.

• 

Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• 

Turn off all controls before unplugging.

• 

Do not

 use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.

•  Connect to a properly grounded outlet only. Refer to “EARTHING/GROUNDING INSTRUCTIONS” on page 3.
• 

Do not

 pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• 

Do not

 use without all filters in place.

• 

Do not

 allow to be used as a toy. Close attention necessary when used by or near children.

EARTHING/GROUNDING INSTRUCTIONS

This appliance must be earthed/grounded. If it should malfunction or breakdown, earthing/grounding provides a path of least resistance 

for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-earthing/grounding 

conductor and earthing/grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and earthed/grounded in 

accordance with all local codes and ordinances.

WARNING

 – Improper connection of the equipment-earthing/grounding conductor can result in a risk of electric shock. Check with a qualified 

electrician or service person if you are in doubt as to whether the outlet is properly earthed/grounded. Do not modify the plug provided with the 

appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Refer to Name Plate for electrical requirements.

• 

USA 120 V

This appliance has a earthing/grounding attachment plug that looks like the 

plug illustrated in Figure 1. Make sure that the appliance is connected to an 

outlet having the same configuration as the plug. No adapter should be used 

with this appliance.

• 

International 120 V

This appliance has an IEC 60309 120 V earthing/grounding attachment plug. 

Make sure that the appliance is connected to an outlet having the same 

configuration as the plug. No adapter should be used with this appliance.

• 

International 220 V – 240 V

This appliance has an IEC 60309 250 V earthing/grounding attachment plug. 

Make sure that the appliance is connected to an outlet having the same 

configuration as the plug. No adapter should be used with this appliance.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Figure 1:  Earthed/Grounded Outlet and Plug

GL_002

Grounded 

Outlet Box

Grounded Outlet

Grounding Pin

Содержание Warthog WGP Series























Отзывы: