Claydon HYBRID T4 Скачать руководство пользователя страница 19

Страница: 19 / 56

CLAYDON TRAILED 4 METRE

Figure 10 – Main screen controls

Figure 11 – Drill lift inhibit screen

In order to allow the drill to pass by an infield obstacle it may be necessary to retract the marker arm

(s) without lifting the drill out of work. To achieve this you must press the Tramline/ marker/ lift inhibit

operation key (10) in Figure 10. The operator will the need to operate the lift spool valve to retract the

marker arm (s), this will not raise the drill, the tramline sequence will not advance and the marker arm

sequence will not advance. Once past the obstacle the operator will need to operate the lower spool

valve to put the marker back out. Once the marker is fully out the operator presses the cancel button

(3), Figure 16; to return to normal operation.

Figure 11 displaying the drill lift inhibit message (displays for 2 seconds every 5 seconds) note that

thetramline nudge button (3) becomes a cancel button to return the drill to normal operation.

1. Setup Menu

2. Go to INFO Screen

3. Go to RATE Screen

4. Go to HYD Screen

5. Number Key Pad

6. Power On/Off Button

7. Pre-Start, starts metering units prior to

moving forward

8. Manual Override Seed Metering (On/Off)

9. Manual Override Fertiliser Metering

(On/Off)

10. Tramline/marker/lift inhibit operation

(see figures 16 and 17)

11. Tramline number nudge (tramlines come

on when on highest number, 4 of 4 in

this case)

12. Backspace key

13. Enter Key

1. Drill Lift inhibit message

2. Tramline/marker/lift inhibit

operation

3. Cancel

Содержание HYBRID T4

























































Результаты поиска

Содержание HYBRID T4

Отзывы:

Бренды по названию

Популярные бренды

Claydon HYBRID T4, Руководство оператора

Результаты поиска

Содержание HYBRID T4

Отзывы:

Бренды по названию

Популярные бренды