Claydon HYBRID M3F Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 60

background image

45

H

IN FIELD OPERATION

OPERATORS MANUAL - HYBRID - M3F & M4RF

Step 4:

Enter the required rate followed by the button as seen in ‘

Figure 4

’

.

Note

: The ISOCAN system can be programmed for use with up to 4 metering channels. Be careful to set

the correct application rate for the correct metering channel.

Figure 4

- Channel Rate setting option

After pressing

a warning screen will pop up to confirm the new maximum forward speed. The

ISOCAN system will now automatically maintain this new application rate irrespective of forward speed.
(within maximum forward speed limits). Please press to dismiss this screen.

You are able to manually override the rate for a selected channel by 5% increments. ‘

Figure 6

’ shows the

buttons which will allow you to increase or decrease the rate. This can be done to a maximum of plus or
minus 50% from the set target rate.

Figure 6

- Manual override buttons

Figure 7

- Return to target rate button

To return to the target rate simply press the button as seen in ‘

Figure 7

’.

Note

: Should you require to increase or decrease the set application rate more than 50%, it is advised to

recalibrate the metering unit for the new 50% set application rate.

Application Rate Setting

Figure 5

- Maximum Forward Speed Warning

«
...
43
44
45
46
47
...
»

Содержание HYBRID M3F





























































Отзывы:

Нет отзывов

Похожие инструкции для HYBRID M3F

Бренд: ABB Страницы: 18

Бренд: R-Tech Страницы: 3

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Campden instruments Страницы: 8

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

Бренд: Campbell Страницы: 2

Бренд: Xo Страницы: 59

Бренд: Falcon Страницы: 8

Бренд: ParaBody Страницы: 3

Бренд: Hach Страницы: 52

Бренд: hager Страницы: 2

Бренд: Jet Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды