background image

 

1. General Information 

1.1  Introduction 

This instruction manual describes the CLAUDGEN 
Surface Warm Air Ceiling Heaters.  

The heater is designed to be suspended from the 
ceiling. 

1.2  General

 

All installations must be in accordance with the 
regulations in force in the country of use. 

These instructions must be handed to the user on 
completion of the installation. 

Installers and service engineers must be able to 
demonstrate competence and be suitably       
qualified in accordance with the regulations in 
force in the country of use. 

To ensure continued and safe operation it is       
recommended that the appliance is serviced    
annually. 
The heater outlet / inlet must not be obstructed 
during use. 

 

1.3

 

Electrical Supply

 

 
Electrical supply is 230/240V single phase,           
Neutral and Earth. The maximum cable inlet size is 
4mm².  
It is recommended that the electrical supply to the 
base unit in the heater is via an appropriate 
switched isolator in accordance with the             
regulations in force in the country of use and must 
be via a fused isolator having a contact separation 
of greater than 3mm on all poles. 
BMS control, time switches, room thermostats and 
door interlocks can be installed at the discretion 
and responsibility of the installer. 
 
All units must be wired in accordance with I.E.E 
regulations for the Electrical Equipment of        
Buildings and the installer should ensure that a   
suitable isolating switch is connected in the mains 
supply. 

1.4 Controller `SL` models 

The HE7237SL, HE7247SL, HE7267SL heaters are   
supplied without a controller. The `SL` models will 
not work without the controller. See section 5.1 for 
more details. 

1.5 Controller `RX` models 

The  HE7237RX,  HE7247RX,  HE7267RX  heaters  are 
supplied without a controller. The `RX` models will 
not work without the controller. See section 5.2 for 
more details. 

 

 

 

1.6  Location 

All units should be installed horizontally. It is       
recommended that the ceiling  heater is          
suspended using four 10mm rods. 
 
Care must be taken to allow complete free air 
movement into the inlet grilles of the unit to      
ensure the correct working operation of the   
heater. If the HE7237SL/RX or HE7247SL/RX heaters 
are mounted close to the wall or corner the     
discharge opening should be facing the wall. The 
minimum distance from the wall or corner is 0.8m 
or 1.2m for the HE7267SL/RX.  

 

1.7  Clearance distances 

 

It is acceptable for the heater to sit flush to the 
ceiling. 
 

The minimum mounting height (floor to grille) is 
2.2m for the HE7237SL/RX, HE7247SL/RX and 2.5m 
for the HE7267SL/RX.  
 
The recommended mounting height is 2.5m for 
the HE7237SL/RX, HE7247SL,RX and 3m for the 
HE7267SL/RX. 

CONSORT SL Controllers 

41001476 Iss 01 

SLPB 

SLTI 

SLVT 

CONSORT Wireless 
controller CRX2 

SLVTB 

Содержание HE7237SL









Отзывы: