Clarke X-Pro CAT213 Скачать руководство пользователя страница 3

Страница: 3 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SPECIFICATION

Please note that the details and specifications contained herein are correct
at the time of going to print. However CLARKE International reserve the right to
change specifications at any time without prior notice.

Model Number

CAT213

Min. Hose Size (ID)

9.5 mm (3/8”)

Operating Pressure

90 psi (6.2 bar)

Air Consumption

6.5 cfm (average)

Max Cutting thickness

1.2 mm /18 Gauge (mild steel)

Min. cutting radius

25 mm

Maximum speed

3800 strokes/minute

Air Inlet Size

1/4“BSP Female

Sound Pressure Level (LpA dB)

79 dB(A)

Sound Power Level (LwA dB)

90 dB(A)

Vibration Levels

4.2 m/s

Vibration Uncertainty K

1.5 m/s

Dimensions (L x W x H)

200 x 100 x 43 mm

Weight 0.84

Содержание X-Pro CAT213

















Результаты поиска

Содержание X-Pro CAT213

Отзывы:

Похожие инструкции для X-Pro CAT213

Бренды по названию

Популярные бренды

Clarke X-Pro CAT213, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание X-Pro CAT213

Отзывы:

Похожие инструкции для X-Pro CAT213

Бренды по названию

Популярные бренды