background image

 5

14.

ALWAYS 

wear proper apparel. Loose clothing or jewellery may

get caught in moving parts. Wear protective hair covering
to contain long hair.

15.

ALWAYS 

use recommended accessories, the use of improper

accessories could be hazardous and invalidate your
guarantee.

16.

ALWAYS 

remove plug from electrical outlet when adjusting,

changing parts, or working on the machine.

17.

NEVER 

operate machine while under the influence of drugs,

alcohol or any medication.

18.

NEVER 

leave machine running unattended. Turn power off.

Do not leave the machine until it comes to a complete stop.

19.

NEVER 

force the machine, it will do a better and safer job at

the rate for which it was designed.

20.

NEVER 

 use power tools in damp or wet locations or  expose

them to rain. Keep your work area well illuminated.

21.

DO NOT

 use in explosive atmosphere (around paint,

flammable liquids etc.). Avoid dangerous environment.

ADDITIONAL PRECAUTIONS FOR PLANERS

1.

ALWAYS 

ensure the cutters are properly secured before use.

2.

ALWAYS 

ensure the cutters are sharp, blunt cutters increase the risk of kick back.

3.

ALWAYS 

switch the machine OFF immediately the task is completed.

4.

ALWAYS

 use with a dust extraction device fitted.

5.

ALWAYS 

allow the machine to reach full speed before commencing work.

6.

DO NOT

 use the machine if the electric cable, plug or motor is in poor condition.

7.

DO NOT

 allow the ventilation slots in the machine to become blocked.

8.

DO NOT 

touch the cutter immediately after use, allow time for it to cool.

9.

NEVER 

leave machine running unattended, 

ALWAYS

 ensure the machine is switched

off and come to a complete stop before leaving it.

10.

NEVER 

proceed unless the workpiece has been thoroughly checked to ensure it is

completely free of nails, screws, staples etc.

11

. AVOID 

accidental starting, by switching off and isolating from the main electrical

supply by removing the plug from the socket. Never load the tool so much that the
motor comes to a standstill.

12.

IMPORTANT! 

This machine develops considerable noise when in use. 

ALWAYS 

wear

Ear Defenders

Additionally, please keep these instructions in a safe place for future reference.

Содержание WOODWORKER CON1020

















Отзывы: