background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

18. Maintain correct balance and footing, DO NOT over reach. Ensure the 

floor is not slippery and wear non-slip shoes.

19. Proper care and maintenance of the ramp is critical to safety.

20. Proper use of this product is critical to safety. Improper use may result in 

personal or property damage which is not covered by the warranty.

21. These ramps are designed to rest against the top edge of your tailgate or 

trailer. If you are not using a bed liner, these RAMPS WILL SCRATCH YOUR 
VEHICLES PROTECTIVE PAINTED SURFACE.

22. These ramps are designed to be used ONLY with the flange facing the 

down (see assembly instructions). To use ramp inverted with flange up (to 
use sides as tyre guides) greatly reduces the weight capacity rating.

WHEN IN VEHICLE RAMP CONFIGURATION - FOLDED

1. DO NOT exceed rated capacity - 800kg per ramp

2. Use only on a hard level surface.

3. Center the load between the sides of the ramp.

4. Use as a matched pair to support one end of a vehicle.

5. Ramps are not to be used to simultaneously support both ends or one side 

of a vehicle.

6. Maximum allowable tyre width is 9".

7. DO NOT use other lifting equipment in conjunction with the ramps.

8. DO NOT disconnect brakes, engine, transmission components, drive train, 

drive shaft, universal joints, or wheels while the vehicle is on the ramps.

9. Make sure the wheels to be driven on to the ramps are in alignment with 

the ramps and center the two ramps against the tyres.

10. Another person, standing clear of the vehicle path, should observe and 

guide the vehicle operator when ascending and descending the ramps.

11. NEVER accelerate or apply brakes suddenly. Proceed slowly and 

cautiously. Once the vehicle reaches the top of the ramps, apply brakes to 
prevent over-travel.

12. Place the vehicle in neutral gear. Release the brakes; the vehicle should 

not move. Set the handbrake to on. Place vehicle in park (or in reverse 
gear for manual transmission). Chock wheels on the ground.

13. Wear gloves. Remove ill fitting clothing, remove ties, watches, rings and 

other loose jewellery and contain long hair.

Содержание STRONG-ARM CFSR500P









Отзывы: