background image

3

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

GENERAL SAFETY PRECAUTIONS

WARNING: The SPP10 pump is not a submersible pump. On no
account should it ever be immersed in water.

Always connect the pump to an earthed power supply via a RCD.

1.

ALWAYS 

keep the pump room clean and well lit. Floors should always be

kept clear. Cluttered or dark areas invite accidents.

2.

NEVER 

over-reach. Keep your proper footing and balance at all times

when installing or maintaining the pump.

3.

NEVER 

direct any water discharge towards electrical wiring or equipment.

4.

ALWAYS 

 thoroughly familiarise yourself with this pump & its operation, and

follow all  instructions in this manual.

 

Never allow persons unfamiliar with

these instructions to operate the pump.

5.

ALWAYS 

ensure that the pump is properly installed to prevent  it from

moving during operation, and that the immediate area surrounding the
pump is kept clear.

6.

ALWAYS

 maintain the pump with care and keep it clean for best / safest

performance.

7.

NEVER 

use this product if any part is damaged. Have it inspected and

repaired by your local Clarke dealer. Always turn the pump off before
carrying out any maintenance.

8.

NEVER 

modify this pump in any way. Use it ONLY for the purpose for which

it is designed.

9.

NEVER 

use for pumping flammable liquids or corrosive chemicals. This

pump is designed to pump clean water only.

10.

NEVER switch the pump ON when the pool is in use. ALWAYS disconnect
the pump from the electrical supply when the pool is in use.

11

.

This pump must be connected to an earthed power supply via a RCD.

12.

ALWAYS 

have the pump serviced by your local CLARKE dealer, using only

identical replacement parts. This will ensure the safety of the pump is
maintained. The use of non standard parts could be hazardous.

Your CLARKE water pump has been designed to give long and trouble free
service. If, however, having followed the instructions in this booklet carefully,
you encounter problems, take the unit to your local CLARKE dealer.

Please keep these instructions in a safe place for future reference.

Содержание SPP10 7175030

















Отзывы: