background image

CLARKE TECHNOLOGY PB-12 Operator's Manual

        Page 3

OPERATOR SAFETY INSTRUCTIONS

WARNING

AVERTISSEMENT

ADVERTENCIA

DANGER:

Failure to read and observe all DANGER statements could result in
severe bodily injury or death.  Read and observe all DANGER
statements found in your Owner's Manual and on your machine.

WARNING:

Failure to read and observe all WARNING statements could result in
injury to you or to other personnel; property damage could occur as
well.  Read and observe all WARNING statements found in your
Owner's Manual and on your machine.

CAUTION:

Failure to read and observe all CAUTION statements could result in
damage to the machine or to other property.  Read and observe all
CAUTION statements found in our Owner's Manual and on your
machine.

DANGER:

Failure to read the Owner's Manual prior to operating or attempting any service or
maintenance procedure to your machine could result in injury to you or to other
personnel; damage to the machine or to other property could occur as well.  You
must have training in the operation of this machine before using it.  If you or your
operator(s) cannot read English, have this manual explained fully before attempting
to operate this machine.

DANGER:

Operating a machine that is not completely or fully assembled could result in injury
or property damage.  Do not operate this machine until it is completely assembled.
Inspect the machine carefully before operation.

DANGER:

Machines can cause an explosion when operated near flammable materials and
vapors.  Do not use this machine with or near fuels, grain dust, solvents, thinners,
or other flammable materials.

DANGER:

Using a machine with a damaged power cord could result in an electrocution.  Do
not use the machine if the power cord is damaged.  To prevent damage to the
power cord, do not move this machine over the power cord.  Always lift the power
cord over the machine.  Do not use the electrical cord to move the machine.

DANGER

:

Electrocution could occur if maintenance and repairs are performed on a unit that
is not disconnected from the power source.  Disconnect the power supply before
attempting any maintenance or service.

DANGER

:

Electrocution or fire could occur if the machine is used on a power circuit that
repeatedly trips or is undersized.  Have a licensed electrician check the fuse,
circuit breaker or power supply, and/or contact your local Clarke distributor for
assistance.

WARNING:

Operating this machine from anywhere other than the back of the machine could result in
injury or damage.  Operate this machine only from the rear.

WARNING:

Machines can topple over if guided over the edges of stairs or loading docks and cause
injury or damage.  Stop and leave this machine only on a level surface.  When you stop
the machine, put all switches into their "OFF" position.

WARNING:

Any alterations or modifications of this machine could result in damage to the machine or
injury to the operator or other bystanders.  Alterations or modifications not authorized by
the manufacturer voids any and all warranties and liabilities.

Содержание PB-12


























Отзывы: