background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

POWER TOOL SAFETY WARNINGS

WORK AREA

1.

Keep the work area clean and well lit. 

Cluttered and dark areas invite 

accidents.

2.

DO NOT operate power tools in explosive atmospheres, such as in the 
presence of flammable liquids, gases or dust. 

Power tools create sparks 

which may ignite the dust or fumes.

3.

Keep children and bystanders away while operating a power tool. 

Distractions can cause you to lose control.

ELECTRICAL SAFETY

1.

Power tool plugs must match the outlet. Never modify the plug in any way. 
Do not use adapter plugs with earthed (grounded) power tools. 

Unmodified 

plugs and matching outlets will reduce the risk of electric shock.

2.

DO NOT expose power tools to rain or wet conditions. 

Water entering a 

power tool will increase the risk of electric shock.

3.

DO NOT abuse the power cable. Never use it for carrying, pulling or 
unplugging the power tool. Keep the power cable away from heat, oil, 
sharp edges or moving parts. 

Damaged or entangled cables increase the 

risk of electric shock.

4.

When operating a power tool outdoors, use an extension cable suitable for 
outdoor use.

 Use of a cable suitable for outdoor use reduces the risk of 

electric shock.

5. If operating the power tool in a damp location is unavoidable, use a 

residual current device (RCD) protected supply.

PERSONAL SAFETY

1.

Stay alert, watch what you are doing and use common sense when 
operating a power tool.

 Do not use a power tool while you are tired or 

under the influence of drugs, alcohol or medication. A moment of 
inattention while operating power tools may result in personal injury.

2.

Use safety equipment. Always wear eye protection.

 Safety equipment such 

as dust mask, non-skid safety shoes, hard hat, or hearing protection used 
for appropriate conditions will reduce personal injuries.

3.

Avoid accidental starting

. Ensure the switch is in the off position before 

plugging in. Carrying power tools with your finger on the switch or plugging 
in power tools that have the switch on invites accidents.

Содержание METALWORKER 6500491













Отзывы: