ELECTRICAL CONNECTIONS
WARNING: THIS MACHINE MUST BE EARTHED.
T
his product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for
connection to a standard, domestic electrical supply.
Should the plug need changing at any time, ensure that a plug of identical
specification is used. IMPORTANT: The wires in the mains lead should be wired up
in accordance with the following colour code:
Green & Yellow ................ Earth
Blue .................................... Neutral
Brown ................................. Live
As the colours of the wires in the mains lead may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
Connect GREEN & YELLOW coloured cord to plug terminal marked
with a letter “E” or Earth symbol “ ”.
Connect BROWN coloured cord to plug terminal marked letter “L”
Connect BLUE coloured cord to plug terminal marked letter “N”
We recommend that this machine is connected to the mains supply through a
Residual Current Device (RCD).
FUSE RATING
The fuse in the plug must ASTA approved to BS1362 and rated at
13 amps
IMPORTANT:
If this appliance is fitted with a plug which is moulded onto the electric cable (i.e.
non-rewireable) :
1.
The plug must be thrown away if it is cut from the electric cable. There is a
danger of electric shock if it is subsequently inserted into a socket outlet.
2.
Never use the plug without the fuse cover fitted.
3.
Should you wish to replace a detachable fuse carrier, ensure that the correct
replacement is used (as indicated by marking or colour code).
4.
Replacement fuse covers can be obtained from your local dealer or most
electrical stockists.
EXTENSION CABLES
If an extension cable is used, always ensure it is fully unwound. When used
outdoors, ensure the extension cable is specifically designed for outdoor use.
The maximum extension length is 25 metres. Ensure that the wire sizes in the cable
are at least 2.5mm
2
in cross section. As a general rule, the extension cable must be
thicker than the cable supplied with the washer.
IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Do not attempt any electrical repairs yourself.
6
MAINTENANCE
WARNING:
Ensure the plug is removed from the socket before carrying out any
adjustment, servicing or maintenance.
AFTER EACH USE
Ensure the hoses and power cable are coiled and properly stowed. DO NOT allow
them to be left casually, in a heap. This invites damage and will cause rapid
deterioration. Take care NOT to drape the hoses/cables over the hot exhaust.
STORAGE
Store the Hot Washer in an horizontal position,
preferably under cover, protected from the elements.
If there is a danger of freezing, the pump should be
filled with antifreeze by inserting the inlet and outlet
hoses into a bucket of antifreeze as shown in Fig.9.
Start the machine and allow the antifreeze to circulate.
After a short time stop the machine and store the
machine with the antifreeze still within the pump body.
11
Fig.9.
2. Limescale
Periodically, check the heating coil for limescale buildup. This will be dependant upon
the relative hardness of your water supply.
When de-scaling is required, use a large water tank as your water supply and add de-
scaler according to the manufacturers instructions.
Remove the lance extension from the handle assembly, place the handle assembly in
the water tank, with the trigger held in the depressed position by some means, and run
the pump and heater for approx. 40 mins.
When completed, switch off the heater, and flush out the system with clean water by
connecting to a water supply or replacing the contaminated water in the water tank.
3. Soot Build up
Poor grades of fuel oil or inadequate combustion will cause heavy build up of soot
on the heating coil. This deposit will insulate the coil and reduce efficiency. It will
restrict air flow through the coil, further aggravating the soot build up. Contact your
CLARKE dealer or CLARKE International Service Dept. when de-sooting is required.
SERVICING
1.Oil burner
It is recommended that the oil burner be serviced yearly, or as needed depending
upon the machines’ usage. Please contact the CLARKE International Service Dept.
on 0208 8988 7400
