Clarke IBC7 Скачать руководство пользователя страница 12

12

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

OPERATION

TO BEGIN CHARGING THE BATTERY

1. Verify the voltage and chemistry of the battery.

2. Confirm that the battery clamps are correctly connected or eyelet 

connectors secure and that the power plug is plugged into a power outlet.

3. All LEDs will flash once after starting and will go into the last memory mode 

automatically after 10 seconds.

4. Press the mode button to toggle to the appropriate charge mode (press 

and hold for three seconds to enter an advanced charge mode) for the 
voltage and chemistry of your battery.

5. The mode LED will illuminate the selected charge mode and the Charge 

LEDs will illuminate (depending on the health of the battery) indicating the 
charging process has started.

6. When connected, the battery charger can stay in place, providing 

continuous charging.

UNDERSTANDING THE CHARGE LEDS

The charger has four Charge LEDs - 25%, 50%, 75% and 100% which indicate 
the connected battery state of charge as shown below.

LED

E

XPLANATION

          25% 50% 75% 100%

The 25% Charge LED (red) will flash when the 
battery is less than 25% charged.
When the battery is 25% charged, the charge 
LED remains on.

          25% 50% 75% 100%

The 50% Charge LED (red) will flash when the 
battery is less than 50% charged.
When the battery is 50% charged, the charge 
LED remains on.

          25% 50% 75% 100%

The 75% Charge LED (red) will flash when the 
battery is less than 75% charged.
When the battery is 75% charged, the charge 
LED remains on.

          25% 50% 75% 100%

The 100% Charge LED (green) will flash when 
the battery is less than 100% charged.
When the battery is 100% charged, the charge 
LEDs will switch off.

Содержание IBC7





















Отзывы: