Clarke HSE120, Инструкция по эксплуатации и обслуживанию, Страница: 3 / 4

you may damage the waterproof seal and invalidate your
guarantee. Repairs must be carried out by your CLARKE
dealer, or contact the CLARKE Service Dep’t, on 0181
556 4443.
If using this pump to pump out a garden pond,
please note that there is a small quantity of oil in
the pump seal. If the pump or seal is damaged,
possibly caused by running the pump dry, oil
may leak out, and appear as a film on the
surface of the water. Although harmless to
people, the oil must be cleared to prevent
any possible harm to pond life. Disconnect
the pump from the electrical supply,
remove it from the pond, and clear the
oil, then contact your CLARKE dealer for
advice.
PARTS LIST & DIAGRAM
HSE 200 & HSE 400 Series
6
Item Description
Part No.
HSE 120 HSE 120A HSE 240 HSE 240A HSE 250A
1 Strainer HG12001 HG120A01 HG24001 HG240A01 HG250A01
2 Centrifugal Switch HG12002 HG120A02 HG24002 HG240A02 HG250A02
3 Pump Housing HG12003 HG120A03 HG24003 HG240A03 HG250A03
4 Impeller HG12004 HG120A04 HG24004 HG240A04 HG250A04
5 Lip Seal HG12005 HG120A05 HG24005 HG240A05 HG250A05
6 Mechanical Seal HG12006 HG120A06 HG24006 HG240A06 HG250A06
7 Oil Chamber HG12007 HG120A07 HG24007 HG240A07 HG250A07
8 Bottom Motor Plate HG12008 HG120A08 HG24008 HG240A08 HG250A08
9 Lower Bearing HG12009 HG120A09 HG24009 HG240A09 HG250A09
10 ‘O’ Ring HG12010 HG120A10 HG24010 HG240A10 HG250A10
11 Rotor Shaft HG12011 HG120A11 HG24011 HG240A11 HG250A11
12 Stator HG12012 HG120A12 HG24012 HG240A12 HG250A12
13 Motor Case HG12013 HG120A13 HG24013 HG240A13 HG250A13
14 Overload Protector HG12014 HG120A14 HG24014 HG240A14 HG250A14
15 ‘O’ Ring HG12015 HG120A15 HG24015 HG240A15 HG250A15
16 Upper Bearing HG12016 HG120A16 HG24016 HG240A16 HG250A16
17 Capacitor HG12017 HG120A17 HG24017 HG240A17 HG250A17
18 Upper Cover HG12018 HG120A18 HG24018 HG240A18 HG250A18
19 Handle HG12019 HG120A19 HG24019 HG240A19 HG250A19
20 Gland Cover HG12020 HG120A20 HG24020 HG240A20 HG250A20
21 Cable Gland HG12021 HG120A21 HG24021 HG240A21 HG250A21
22 Power Cable HG12022 HG120A22 HG24022 HG240A22 HG250A22
23 Discharge Outlet HG12023 HG120A23 HG24023 HG240A23 HG250A23
3
ELECTRICAL CONNECTIONS
All models EXCEPT HSE 250A , should have their mains lead connected to a standard
230Volt (50Hz) electrical supply through an approved plug or a suitably fused
isolator switch. We recommend that these pumps be fitted with a Residual Current
Device (RCD).
NOTE: This is mandatory when pump is used for pumping swimming pools.
Model HSE250A must be connected to a protected 110V supply, through a suitably
approved connector. On no account must a 230V, 13amp (BS1363) plug be used.
NOTE: If a portable 110V transformer is used, make sure it has a rated capacity
sufficient to take the load of the pump.
In the event that the pump is hard wired into the electrical system, it must be
carried out in accordance with IEE regulations.
If used for draining swimming pools or ponds, the pump MUST be fitted with a
Residual Current Device (RCD), with a rated residual operating current of no
greater than 30mA.
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in the mains lead are coloured in accordance with the
following code: Green & Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the flexible cord of this appliance may not correspond with the
coloured markings identifying terminals in your plug proceed as follows:
Connect GREEN & YELLOW coloured cord to plug terminal marked with a
letter “E” or Earth symbol “ “ or coloured GREEN or GREEN & YELLOW.
Connect BROWN cord to terminal marked with a letter “L” or coloured RED
Connect BLUE cord to terminal marked with a letter “N” or coloured BLACK
The fuse in the plug for this appliance must be rated at 13 amps .
If this appliance is fitted with a plug which is moulded onto the electric cable (i.e.
non-rewirable) please note:
1. The plug must be thrown away if it is cut from the electric cable. There is a
danger ofelectric shock if it is subsequently inserted into a socket outlet.
2. Never use the plug without the fuse cover fitted.
3. Should you wish to replace a detachable fuse carrier, ensure that the correct
replacement is used (as indicated by marking or colour code).
4. Replacement fuse covers can be obtained from your local dealer or most
electrical
5. The fuse in the plug must be replaced with one of the same rating ( 13 amps )
and this replacement must be ASTA approved to BS1362.
IMPORTANT: If in doubt, consult a qualified electrician.