manualshive.com logo in svg

Clarke CTS15, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke CTS15 Скачать руководство пользователя страница 17

17

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

OPERATION

ON/OFF SWITCH

1. To turn the saw on, press the 

green start button “I”. 

• Wait for the blade to reach its 

maximum speed before 
commencing with the cut.

2. To turn the saw off, press the red 

stop button “0”.

NOTE:

The blade will spin for several 
seconds after the machine is 
switched off.

MOTOR BRAKE

The motor is fitted with a brake which should stop the saw blade in under 10 
seconds. 

If this time is exceeded, the brake must be repaired by an authorised service 
centre. 

A saw with a defective brake must not be used.

CAUTION: BEFORE STARTING THE SAW ALWAYS CHECK THE FOLLOWING 
POINTS:

1. Is the saw blade firmly tightened?

2. Are all the locking levers firmly locked?

3. Is the riving knife aligned with the saw blade?

4. Is the blade guard fitted?

5. Make sure that the fences are not touching the saw blade.

6. Can the blade rotate freely? 

7. Are there any wood pieces jammed between the blade and the 

table insert?

8. Have all loose workpieces been removed from the table saw?

9. Have all the setting tools been removed?

10. Wear protective goggles, ear protection and dust mask.

Содержание CTS15





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды