Clarke CONRHD720 страница 12 Скачать руководство пользователя

Страница: 12 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

BEFORE USE

1. Ensure all fixing screws remain tight to maintain a safe working condition.

2. Inspect the power cable to ensure it is sound and free from cracks, bare

wires etc.

CLEANING

1. Ensure all air ventilation slots are clear of blockages, (use compressed air to

clean the machine if possible).

2. After use, clean all dust and swarf from the drill.

3. Clean the exterior of the drill with a soft cleaning cloth. Never use any

chemicals or harsh abrasives to clean the tool.

• Avoid using solvents when cleaning plastic parts, most plastics are

susceptible to damage from the various types of commercial
solvents.

GENERAL MAINTENANCE

• All bearings etc, in this tool are lubricated with a sufficient amount of

high grade lubricant for the tools lifetime under normal operating
conditions, therefore no further lubrication is necessary

• Refer to your CLARKE dealer if internal maintenance is required.

INDICATORS

The

Green

indicator is a 'Power

present' indicator. This illuminates
when the product is plugged into a
live socket.

The

Red

indicator is a brush wear

indicator. It illuminates when the
motor brushes need replacing, Refer
to your clarke dealer.

WARNING: MAKE SURE THAT THE 5 FUNCTION ROTARY HAMMER DRILL IS
SWITCHED OFF AND DISCONNECTED FROM THE MAINS SUPPLY BEFORE
STARTING ANY CLEANING OR MAINTENANCE PROCEDURES.

Содержание CONRHD720

















Результаты поиска

Содержание CONRHD720

Отзывы:

Похожие инструкции для CONRHD720

Бренды по названию

Популярные бренды

Clarke CONRHD720, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание CONRHD720

Отзывы:

Похожие инструкции для CONRHD720

Бренды по названию

Популярные бренды