Clarke CIG81020 Скачать руководство пользователя страница 13

Страница: 13 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

5. Insert the hook on the ratchet into the hole on the bent corner leg. Wind

the ratchet so that the webbing overlaps itself.

6. Slide the bottom Cross Rails through the fabric pockets at each leg and re-

attach with clamps at each leg. Repeat this on the other side. Push down
on the cover rails to tighten the cover before tightening the bolts
completely.

7. When the cover rails are all secured, proceed to the four corners and

tighten the end covers to the end frames using the ratchet action.

NOTE:

Over-tightening can cause damage to straps and/or the anchor

point. Do not over-tighten!

The garage is now ready for use.

NOTE:

Check periodically (two to three times in the first week and

tighten ratchet tie-downs and all hardware as needed. Monthly
inspection is recommended throughout usage.

Содержание CIG81020

















Результаты поиска

Содержание CIG81020

Отзывы:

Бренды по названию

Популярные бренды

Clarke CIG81020, Руководство по сборке

Результаты поиска

Содержание CIG81020

Отзывы:

Бренды по названию

Популярные бренды