Clarke CIG81020 Скачать руководство пользователя

Страница: 10 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

STEP 5: INSTALLING THE FRONT AND BACK COVERS

The front cover has a zippered door to allow entry to the garage. Be sure to
locate this cover at the desired end and ensure the zipper is in the closed
position while installing.

The back cover is a solid piece of polyethylene. Both the covers are installed in
the same fashion.

1. Thread the strap through the spindle of the ratchet to make sure the strap

will stay in the sleeve when assembled. Raise and lower the handle two or
three times to wind the strap onto the spindle as above.

2. Begin with the front cover and first locate the webbed belt that runs

around the perimeter of the cover.

• The webbing is exposed at the peak, the shoulders and the feet of

the cover.

3. Using a rubber mallet, disconnect the apex tube (#4) from the connector

(#12) located between the leg and the roof tubes.

Содержание CIG81020

















Результаты поиска

Содержание CIG81020

Отзывы:

Похожие инструкции для CIG81020

Бренды по названию

Популярные бренды

Clarke CIG81020, Руководство по сборке

Результаты поиска

Содержание CIG81020

Отзывы:

Похожие инструкции для CIG81020

Бренды по названию

Популярные бренды