manualshive.com logo in svg

Clarke CIG81015, Руководство по сборке

Поделиться
Скачать
Clarke CIG81015 Скачать руководство пользователя страница 13

13

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

4. Slip the webbing strap between tube #5 and the connector (as shown in 

Diagram I). Rejoin the tubes.

5. Repeat this step for the opposite shoulder.

6. Move to the apex of the garage using a step ladder and using a rubber 

mallet, disconnect the apex tube (#4a) from the connector (#12). Slip the 
webbing strap between the tubes (see Diagram I detail 2) and reconnect.

7. While one person remains on the steps and standing at the peak of the 

garage, the other person inserts the hook of the ratchet straps into both 
sides of corner legs at (detail I-3).

The person standing at the apex assists by ensuring the cover is partially folded 
over the tubes of the end frame and inside or toward the interior of the 
garage.

The other person makes sure the door panel is flat and then tightens the 
ratchet straps. (Diagram I detail 3).

STEP 6: INSTALLING THE MAIN COVER

1. Lay the cover on the 

ground next to the frame 
with inside of the cover (the 
side with pipe pockets) 
facing upward and the 
webbing on the front and 
rear of the corner of the 
building.

2. Tie one end of a rope to 

the eyelets on one corner 
of the cover, then another 
rope to the other corner 
eyelets.

Содержание CIG81015

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды