Clarke CHD850 Скачать руководство пользователя страница 12

Страница: 12 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

FAULTFINDING

Problem

Possible Cause

Remedy

Tool will not operate

No power supply

Check supply & rectify as
necessary

Switch is faulty

Consult your Clarke
dealer

Fuse blown

Check & replace if neces-
sary

Motor is faulty

Consult your Clarke
dealer

Motor runs but drill bit
does not move.

Drill fastening not tight.

Secure drill bit.

Drive gear broken

Consult your Clarke
dealer

Heavy internal sparking

Faulty motor

Consult your Clarke
dealer

Warn brushes

Consult your Clarke
dealer

Motor becomes hot

Unduly heavy use

Reduce the force applied
to the tool. Let the tool do
the work.

Air vent have become
blocked.

Clean out the air vents
using compressed air or
clean with a dry cloth.

Low supply voltage

Ensure supply voltage is
correct. If an extension
cable is used, ensure it is
the correct rating and is
fully unwound.

Excessive vibration.

Drill bit bent or not
mounted correctly.

Check and rectify.

Machine bearings worn. Consult your Clarke

dealer

CHD850 Hammer Drill rev 4.fm Page 12 Monday, February 9, 2015 10:47 AM

Содержание CHD850

















Результаты поиска

Содержание CHD850

Отзывы:

Бренды по названию

Популярные бренды

Clarke CHD850, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание CHD850

Отзывы:

Бренды по названию

Популярные бренды