background image

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

5. When emptying, grip the tilt angle 

wheel firmly and tilt the wheel to 
disengage the locking pins.

6. Use the wheel to tip the mixer 

drum forward.

• Only discharge the mixer when 

a suitable receptacle for the 
cement mix is in position.

• Do not operate this machine 

on a steep gradient. Always 
stand the mixer on firm, level ground where it cannot tip over. 

• Always keep water well away from the motor and other electrical 

components.

It is essential that the mixer is kept clean. Dried cement inside the drum will be 
very difficult to remove. For the mixer to perform at its best it must be 
thoroughly cleaned after every use.

CARE AND MAINTENANCE

BEFORE STARTING WORK

Inspect the power cable and ensure it is free from damage and is not in 
danger of being damaged by vehicles, equipment or other operations taking 
place on the work site.

AFTER USE

It is essential that the machine is hosed down thoroughly with clean water, 
being sure to remove all traces of cement mix especially from around the 
mixing blades, Take care to prevent water from entering the motor housing 
and if necessary, wrap a polythene sheet or bag over it during cleaning.

Re-tighten the drive belt after the first 25 hours use. The belt should be able to 
be deflected no more than 1/4 inch.

PERIODICALLY

After extensive use, inspect the paintwork and remove any rust that may be 
apparent before touching up where necessary with a rust resistant paint.

WARNING: REMEMBER THAT THE CENTRE OF GRAVITY OF THE LOADED 
MIXER MAY PRESENT A HAZARD WHEN OPERATING ON UNEVEN GROUND.

Содержание CCM110

















Отзывы: