manualshive.com logo in svg

Clarke APK900, Инструкция по эксплуатации и обслуживанию

Поделиться
Скачать
Clarke APK900 Скачать руководство пользователя страница 9

9

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

OPERATION

GENERAL PREPARATION

Do not use textured wall paints or coatings as they are likely to block the
nozzle. To obtain the best results, it is important that you prepare the surface
to be sprayed and thin the paint to the correct viscosity before you operate
your spray gun. Always ensure that the surfaces to be sprayed are free from
dust, dirt and grease. Make sure that you have masked the areas that should
not be sprayed, using a good quality masking tape.

Paint to be sprayed should be thoroughly mixed and free from lumps or other
particles. Many substances can be sprayed with this spray gun, but always
check the manufacturers recommendations before purchasing your paint.

PAINT PREPARATION

ALWAYS REMEMBER TO DISCONNECT FROM THE MAINS SUPPLY BEFORE
FILLING THE PAINT CONTAINER WITH SPRAYABLE MATERIALS.

Most paints are supplied ready for brush application and will need to be
thinned before they are suitable to be sprayed. Follow the manufacturers
advice on thinning the paint when used with a spray gun. Using the viscosity
cup will help you to determine the correct viscosity of paint to be used.

To do this, fill the cup to the brim with the paint and measure the amount of
time it takes for the cup to empty back into the can. The table below shows
recommended times for different materials.

Material

Runout Time

Emulsion paints

18 - 22 seconds

Thinner-soluable primers

25 - 40 seconds

Thinner-soluable varnishes

15 - 40 seconds

Water-soluable primers

25 - 40 seconds

Water-soluable varnishes

20 - 35 seconds

Automotive spray paint

20 - 35 seconds

Wood preservatives

No thinning required

Wood stains

No thinning required

If the paint takes longer than the recommended time to empty, further
thinning is required. Mix in a small quantity of the appropriate thinner and
repeat the viscosity test until the correct thickness is achieved. Some
sprayable materials contain particles and lumps which should be strained
before filling the paint container.

Содержание APK900





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды