manualshive.com logo in svg

Clarke 8130535, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke 8130535 Скачать руководство пользователя страница 20

20

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

GENERAL CARE

1. Check all cables periodically; they must be in good condition and not 

cracked.

2. Always ensure the generator’s air vents are completely clear. Brush away 

any dust which may have accumulated.

The engine requires periodic servicing. Please refer to the engine manual for 
details.

If the machine is not going to be used for some time the engine must be 
adequately prepared. Please refer to the engine manual for details.

IMPORTANT: ALWAYS switch the engine OFF before servicing or cleaning

ELECTRICAL TROUBLE SHOOTING

ENGINE TROUBLESHOOTING

Consult the suppliers engine manual.

Problem: No AC Output

CAUSE

REMEDY

Selector switch in the wrong position.

Set selector switch

Tripped circuit breaker

Re-set AC safety trip

Poor connection or damaged lead

Check connection and or 
replace lead

Broken AC connector

Contact CLARKe service dept

Faulty circuit breaker

Contact CLARKe service dept

Problem: Erratic supply

CAUSE

REMEDY

Incorrect engine rpm

Set engine rpm. Consult your 
CLARKE dealer

Alternator defect

Contact CLARKe service dept

Содержание 8130535

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды